mypros+
Error code reference

GE Washer Error Code E59

No signal from speed analyzer for 3 seconds.

GE codesGE washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E59 error code actually means

Your GE washer lost track of how fast its motor was spinning and couldn't detect any speed information for 3 seconds, so it stopped the cycle to protect itself. This usually means something is wrong with the motor, the belt that connects the motor to the drum, or a small sensor that monitors motor speed. A technician will need to inspect these parts to find the cause.

Diagnostic procedure

The full E59 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Remove motor belt and check if motor pulley turns freely (refer to Test 12).
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E59 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E59

Ranked by how often they cause this code
  1. 1Broken or worn drive belt
  2. 2Failed speed sensor (tachometer)
  3. 3Seized or failing motor
  4. 4Loose or damaged wiring harness
  5. 5Faulty main control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E59

What does E59 mean on a GE washer?
E59 means the washer's control board received no signal from the speed analyzer for 3 consecutive seconds. The speed analyzer monitors how fast the motor is spinning, and without that data the washer cannot safely continue a cycle. The machine shuts down to prevent potential damage to the motor or other components.
Is it safe to use my GE washer while it shows E59?
No, you should not attempt to run the washer while E59 is active. The error indicates the control system cannot confirm motor speed, which means it cannot properly manage the cycle. Running the machine in this state risks damaging the motor, the control board, or other drive components.
How much does it cost to repair a GE washer with error code E59?
Repair costs vary depending on which component has failed. A replacement drive belt is typically an inexpensive part, often in the range of $10 to $30. A new speed sensor or motor wiring harness repair might run $50 to $150 including labor. Motor replacement is more significant, potentially ranging from $150 to $400 or more depending on the model and local labor rates.
Can I fix E59 on my GE washer myself?
Some causes of E59 are DIY-friendly, such as replacing a broken drive belt or reseating a loose wiring connector. Replacing the speed sensor is also manageable for experienced DIYers. However, motor replacement or control board diagnosis typically requires electrical testing equipment and comfort working with appliance internals, so those repairs are better suited to a technician.
Will resetting the washer clear the E59 error code?
A reset may temporarily clear the code from the display, but if the underlying cause is not repaired, E59 will return as soon as the washer attempts to run a cycle and fails to detect a speed signal again. Resetting is useful as a diagnostic step to confirm the fault is repeatable, but it is not a fix.

Related GE washer error codes

All GE washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass