mypros+
Error code reference

Goodman Heat Pump Error Code d3

Configuration mis-match

Goodman codesGoodman heat pump codes

Configuration mis-match - shared data sent to integrated control module does not match hardware configuration.

First step from the service manual

Verify system type. Verify shared data is correct for specific model; re-populate data if required.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for d3.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What d3 means on a Goodman heat pump

The D3 fault code on a Goodman heat pump indicates a configuration mismatch between the shared data stored in the system and the hardware configuration that the integrated control module (ICM) detects. The integrated control module serves as the central communication and control hub for the heat pump system, coordinating operation between major components. When the ICM reads shared data that does not correspond to the actual hardware present, it triggers this fault to prevent incorrect operation that could damage components or result in improper system performance.

Shared data in these systems is a set of configuration parameters that defines the system type, capacity, and feature set. This data must precisely match the physical hardware installed. A mismatch typically occurs after a control board replacement, a failed data population procedure, or when a replacement component with pre-loaded data from a different model is installed. The ICM continuously cross-references this shared data against its hardware detection routines, so even a subtle discrepancy will trigger the D3 code.

The first diagnostic step is to verify the system type being serviced and confirm that the shared data loaded into the ICM matches the specific model number. If the data is incorrect or has become corrupted, it must be re-populated using the correct configuration for that unit. This process requires identifying the exact model, accessing the configuration parameters, and rewriting the shared data to align with the installed hardware.

Source: manufacturer service documentation.

Common causes of d3

  1. 01

    Incorrect or missing shared data after control board replacement

    Wiring / connection

    When an integrated control module is replaced, the shared data configuration must be re-populated to match the specific model. If this step is skipped or done incorrectly, the D3 fault will appear immediately.

  2. 02

    Replacement component pre-loaded with mismatched configuration

    Wiring / connection

    A replacement ICM or associated module shipped with factory-default or different-model configuration data will conflict with the installed hardware, triggering this code upon startup.

  3. 03

    Corrupted shared data

    Wiring / connection

    Power surges, voltage irregularities, or an incomplete prior programming attempt can corrupt the stored shared data, causing the ICM to read a configuration that no longer matches the hardware.

  4. 04

    System type set incorrectly for the installed unit

    Wiring / connection

    If the system type parameter was configured for a different capacity or feature set than what is physically installed, the ICM will detect the mismatch and set the D3 fault. Verify the system type selection matches the model number exactly.

  5. 05

    Faulty integrated control module

    Part replacement

    In rare cases, an ICM that has failed internally may misread its own hardware detection routines, producing a false configuration mismatch. This is typically suspected only after correct shared data has been confirmed and re-populated without resolving the fault.

See the test procedure for each cause

Frequently asked questions about d3

What does d3 mean on a Goodman heat_pump?
The D3 code on a Goodman heat pump indicates a configuration mismatch, meaning the shared data stored in the integrated control module does not match the hardware configuration the system detects. This prevents the unit from operating incorrectly due to mismatched settings. A technician needs to verify the system type and re-populate the shared data with the correct configuration for the specific model installed.
Can I fix a D3 error on my Goodman heat pump myself?
Resolving the D3 fault requires accessing and reprogramming the shared data in the integrated control module, which is a procedure specific to Goodman equipment and requires technical knowledge of the system type and configuration parameters. This is generally not a homeowner-level repair. A qualified HVAC technician familiar with Goodman integrated control systems should perform the diagnosis and data re-population.
Will resetting the Goodman heat pump clear the D3 error code?
A simple power reset will not clear the D3 fault because the underlying configuration mismatch remains in the control module even after power is removed and restored. The ICM will detect the same discrepancy on startup and re-trigger the fault. The shared data must be corrected and re-populated before the code will clear.
Is it safe to run my Goodman heat pump with a D3 error code?
The D3 fault is a configuration protection fault, meaning the system flags this condition to prevent operation under a mismatched setup that could cause improper component behavior or damage. The unit will typically not operate normally while this fault is active. It is best to leave the system off and have a technician correct the configuration before resuming normal operation.
How much does it cost to repair a D3 error on a Goodman heat pump?
If the fault is resolved simply by re-populating the correct shared data, the cost is typically limited to a diagnostic and labor fee, which can range from around $75 to $200 depending on your area and the technician. If the integrated control module itself has failed and requires replacement, parts and labor costs can range from $300 to $700 or more. Getting an accurate diagnosis first will clarify which repair is needed.

Related Goodman heat pump codes

All Goodman heat pump codes
View all 28 Goodman heat pump codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass