mypros+
Error code reference

Maytag Dryer Error Code F2E5

UI software error

Maytag codesMaytag dryer codes

UI software error: parameter memory invalid.

First step from the service manual

Replace the User Interface.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F2E5.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F2E5 means on a Maytag dryer

The F2E5 error code on a Maytag dryer indicates a User Interface (UI) software error specifically related to invalid parameter memory. This fault originates within the control board or display assembly that makes up the UI, where stored configuration parameters have become corrupted, unreadable, or otherwise invalid. The UI relies on a section of non-volatile memory to retain operational settings and calibration data. When the dryer's internal diagnostic routine reads that memory and finds it does not match expected values or is completely unreadable, it triggers the F2E5 fault.

This type of error is distinct from a general communication failure between the UI and the main control board. F2E5 points specifically to the integrity of the parameter data stored within the UI itself. Common triggers include voltage spikes or power surges that corrupt the onboard memory, a manufacturing defect in the UI assembly, or memory degradation over time. In some cases, a brief power interruption during a write cycle can leave memory in an invalid state.

Because the fault is tied directly to the UI's internal memory, a power reset rarely resolves it permanently. The primary corrective action is replacement of the User Interface assembly. Attempting to continue operating the dryer with this fault active may result in unpredictable behavior, incorrect cycle execution, or the inability to select and run cycles properly.

Source: manufacturer service documentation.

Common causes of F2E5

  1. 01

    Corrupted UI parameter memory

    Part replacement

    The most direct cause of F2E5 is corruption of the non-volatile memory stored within the UI board itself. This can occur due to a power surge, an interrupted write cycle, or gradual memory cell degradation, and it cannot be repaired through reprogramming in the field.

  2. 02

    Power surge or voltage spike

    Part replacement

    A sudden surge in household voltage can write invalid data to the UI's memory registers. If the error appeared shortly after a storm, power outage, or electrical event, this is a likely contributor.

  3. 03

    Failed or defective UI assembly

    Part replacement

    The UI circuit board itself may have a hardware failure affecting the memory chip or its supporting circuitry. This can occur as a manufacturing defect or as a result of component wear over time.

  4. 04

    Loose or intermittent UI wiring connection

    Wiring / connection

    Although less common for a parameter memory fault, a loose ribbon cable or connector between the UI board and the main control board can sometimes cause communication issues that present as UI errors. Inspect connectors for corrosion or poor seating before ordering parts.

See the test procedure for each cause

Frequently asked questions about F2E5

What does F2E5 mean on a Maytag dryer?
F2E5 on a Maytag dryer means the User Interface has detected that its parameter memory is invalid or corrupted. This is a software-level fault within the control panel assembly itself. The dryer's diagnostic system found that the stored configuration data does not match valid expected values, which prevents normal operation.
Can I fix F2E5 myself on a Maytag dryer?
The fix for F2E5 is replacement of the User Interface assembly, which is a task many experienced DIYers can handle. The process typically involves disconnecting power, removing the control panel housing, unplugging the wiring harness from the old UI board, and installing the new assembly. Always disconnect power to the dryer before beginning any repair.
Will resetting my Maytag dryer clear the F2E5 error?
A power reset, such as unplugging the dryer for a few minutes, may temporarily clear the fault display, but it will not resolve the underlying corrupted parameter memory in the UI. The error is very likely to return because the root cause is a hardware or memory integrity issue within the UI board itself.
Is it safe to use my Maytag dryer with an F2E5 error?
Operating the dryer with an active F2E5 fault is not recommended. Because the UI parameter memory is invalid, the dryer may not execute cycles correctly, which could result in uncontrolled heating behavior or the inability to run a complete cycle. It is best to stop using the dryer until the UI is replaced.
How much does it cost to fix a Maytag dryer F2E5 error?
The cost to fix F2E5 depends on whether you replace the UI yourself or hire a technician. A replacement User Interface assembly for a Maytag dryer typically ranges from around $50 to $200 or more depending on the specific model. If you hire a professional, expect to add $100 to $200 in labor costs on top of the part price.

Related Maytag dryer codes

All Maytag dryer codes
View all 251 Maytag dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass