mypros+
Error code reference

Maytag Washer Error Code 90

Overflow condition detected

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 90 error code actually means

Your Maytag washer detected that the water level inside the drum got dangerously high, so it stopped the cycle to protect your home from flooding. This usually means water kept flowing in when it should have stopped, or a sensor gave the wrong reading. Check for water on the floor around the machine and do not restart it until the cause is identified.

Diagnostic procedure

The full 90 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check water valve. Check pressure switch and air dome hose. Check for siphoning.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 90 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 90

Ranked by how often they cause this code
  1. 1Faulty water inlet valve
  2. 2Siphoning through drain hose
  3. 3Defective pressure switch
  4. 4Damaged or disconnected air dome hose
  5. 5Control board malfunction

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 90

What does 90 mean on a Maytag washer?
Error code 90 means the washer has detected an overflow condition, with the water level rising higher than the safe maximum. The control board monitors water level through a pressure switch and air dome hose system, and when the reading exceeds the allowable limit, the machine stops and displays this code. The three primary areas to investigate are the water inlet valve, the pressure switch with its air dome hose, and the drain hose installation for siphoning issues.
Is it safe to use my Maytag washer when error code 90 appears?
No, you should not run the washer until the cause of the overflow condition is identified and corrected. An active overflow condition can result in water damage to your floor, walls, and surrounding cabinetry. Leave the washer powered off and check for standing water around the machine before beginning any diagnosis.
Will resetting my Maytag washer clear error code 90?
A reset may temporarily clear the error code from the display, but it will not resolve the underlying cause. If the water inlet valve is leaking, the pressure switch is defective, or a siphoning condition exists, the error will return as soon as the washer attempts to fill again. Always diagnose and correct the root cause before attempting to run a new cycle after a reset.
Can I fix error code 90 on my Maytag washer myself?
Some causes of error code 90 can be addressed without professional help. Checking the drain hose for proper installation and correcting a siphoning issue is a straightforward DIY fix. Inspecting the air dome hose for cracks or loose connections is also manageable for most homeowners. However, replacing a water inlet valve or pressure switch requires basic appliance repair skills and comfort working with electrical components and water supply connections.
How much does it cost to repair error code 90 on a Maytag washer?
Repair costs vary depending on the cause. Correcting a drain hose siphoning issue costs nothing if you do it yourself. A replacement water inlet valve typically costs between $30 and $80 for the part, while a pressure switch generally runs between $20 and $60. If you hire a technician, expect to add $100 to $200 in labor costs on top of any parts, depending on your location and the complexity of the repair.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass