mypros+
Error code reference

Samsung Washer Error Code Hot&Cold LED Flash

Motor driving code and TMR sensor code

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Hot&Cold LED Flash error code actually means

Your Samsung washer is detecting a problem with the motor that spins the drum and the sensor that monitors how fast it is spinning. The machine cannot complete a spin cycle because something is preventing the motor from working correctly. This could be a loose wire connection, something stuck in the motor, or a worn-out motor component that needs replacement.

Diagnostic procedure

The full Hot&Cold LED Flash procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check the motor connector terminal connections and check if the Motor Cover State is damaged.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Hot&Cold LED Flash procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Hot&Cold LED Flash

Ranked by how often they cause this code
  1. 1Disconnected PBA or Motor Connector Terminal
  2. 2Foreign Material Inside the Motor
  3. 3Damaged Motor Internal Coil
  4. 4TMR Sensor Terminal Not Connected
  5. 5Motor Overloaded or Spin Net Not Engaged

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Hot&Cold LED Flash

What does Hot&Cold LED Flash mean on a Samsung washer?
The simultaneous flashing of the Hot and Cold LEDs on a Samsung washer signals a fault in the motor drive circuit or the TMR tachometer sensor circuit. The washer's control board has detected that the motor is not operating correctly, which prevents the drum from spinning. Causes range from a disconnected connector or loose sensor terminal to a damaged motor coil or mechanical obstruction inside the motor housing.
Is it safe to keep using my Samsung washer when this error appears?
You should not continue running the washer when this error is active. The motor is not functioning properly, and running the appliance could worsen an existing coil fault, cause additional electrical damage to the control board, or allow a mechanical problem to escalate. Diagnose and resolve the issue before resuming normal use.
Will resetting my Samsung washer clear the Hot&Cold LED Flash error?
A power reset may temporarily clear the error display, but the fault will return if the underlying problem is not resolved. If the issue is a disconnected terminal that reseats itself during movement, the error may not immediately reappear, but an overloaded motor, damaged coil, or faulty TMR sensor connection will continue to trigger the code on subsequent cycles. A proper physical inspection of the motor and its connections is necessary for a lasting fix.
Can I fix the Hot&Cold LED Flash error myself?
Some causes of this error are DIY-friendly, particularly checking and reseating disconnected or loose connector terminals at the motor and PBA, and clearing any foreign material from inside the motor. However, diagnosing a short-circuited or open motor coil requires a multimeter and some electrical knowledge, and replacing a damaged motor is a more involved repair that may be better handled by a technician.
How much does it cost to repair the Hot&Cold LED Flash error on a Samsung washer?
Repair costs vary widely depending on the root cause. If the fix is simply reseating a loose connector or removing debris from the motor, costs may be minimal or limited to a service call fee in the range of $75 to $150. Motor replacement is significantly more expensive, typically ranging from $200 to $450 or more depending on the specific model and labor rates in your area.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass