mypros+
Error code reference

Samsung Washer Error Code Hot&Large LED Flash

Door code

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Hot&Large LED Flash error code actually means

Your Samsung washer is showing this error because the door did not lock properly when the cycle was about to start. The washer won't run until it can confirm the door is securely closed and locked. This is usually caused by a faulty door lock part or a loose wire connection, both of which can often be repaired without replacing major components.

Diagnostic procedure

The full Hot&Large LED Flash procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check whether the door lock switch unit is inserted and whether it is damaged.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Hot&Large LED Flash procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Hot&Large LED Flash

Ranked by how often they cause this code
  1. 1Door lock switch unit not fully inserted or damaged
  2. 2Broken or incorrectly connected switch terminal
  3. 3Wiring harness damage or leakage
  4. 4Failed door lock switch unit
  5. 5Main PCB fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Hot&Large LED Flash

What does Hot&Large LED Flash mean on a Samsung washer?
The Hot&Large LED Flash error indicates a door locking failure. After the door was closed, the washer could not confirm that the door lock engaged successfully. This is caused by a faulty door lock switch, a terminal connection problem, wiring issues, or in rare cases a main PCB fault. The washer will not operate until the door locking condition is resolved.
Is it safe to use my Samsung washer when this error is showing?
No, you should not attempt to run the washer while this error is active. The door lock fault means the control system cannot confirm the door is secured, and the washer is designed to prevent operation in this state. Attempting to bypass this condition could be unsafe and may cause further damage to the control system or wiring.
Will resetting the washer clear the Hot&Large LED Flash error?
A reset may temporarily clear the error display, but if the underlying fault in the door lock circuit is still present, the error will return as soon as the washer attempts to lock the door again. A reset is useful for confirming whether the fault is intermittent, but it is not a fix. The door lock switch, wiring, and connections need to be inspected and repaired to resolve the error permanently.
Can I fix the Hot&Large LED Flash error myself?
In many cases, yes. Start by checking that the door lock switch unit connector is fully inserted and that the switch shows no visible damage. If a terminal is loose or a wire is visibly damaged, those are repairs a knowledgeable DIYer can address. If the switch unit itself has failed internally, replacing it is a moderately straightforward repair, though working inside the washer cabinet does require comfort with basic appliance disassembly.
How much does it cost to repair the Hot&Large LED Flash error?
If the fix is a reseated or replaced connector, the cost may be minimal, mainly your time. A replacement door lock switch unit typically costs in the range of $20 to $60 for the part. If a wiring harness section needs replacement, costs can range from $30 to $100 or more depending on the harness. Main PCB replacement is the most expensive possibility, often ranging from $150 to $350 or higher for parts alone, plus any labor costs if a technician is involved.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass