Skip to main contentGet Started
Error code reference
Whirlpool Dishwasher Error Code 7-7
Flowmeter problem
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
What the 7-7 error code actually means
The 7-7 code means your dishwasher is having trouble reading how much water is flowing into the machine. This is caused by a faulty or disconnected sensor called a flowmeter. A technician will need to test the sensor and its wiring to determine whether the flowmeter or the control board needs to be replaced.
Diagnostic procedure
The full 7-7 procedure
Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.
MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
1. Disconnect power or unplug unit. 2. Check connections at salt level sensor and at flowmeter. 3. Use meter to check for flowmeter switch closed and salt level sensor. 4. Disconnect flowmeter and leave salt sensor connected. Apply a magnet to side of salt tank near the sensor connection to force the switch closed. 5. Run complete service diagnostics cycle. If sanitized LED turns on in interval 3, replace the flowmeter assembly. If not, replace the control.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 7-7 procedure $9.95
Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.
Most common causes of 7-7
Ranked by how often they cause this code
- 1Loose or disconnected wiring connection
- 2Failed flowmeter switch
- 3Damaged flowmeter assembly
- 4Faulty salt level sensor
- 5Defective control board
Most DIYers save hundreds by diagnosing before ordering parts.
Get Started
$29/month · Cancel anytime · Or $9.95 3-day pass
Questions people ask about 7-7
What does 7-7 mean on a Whirlpool dishwasher?
The 7-7 code on a Whirlpool dishwasher indicates a flowmeter problem, meaning the control board is not receiving a proper signal from the flowmeter. This can be caused by a disconnected wiring harness, a damaged flowmeter switch, or in some cases a faulty control board. The dishwasher will not operate normally until the fault is resolved. A specific diagnostic sequence involving the salt level sensor and a magnet test is used to pinpoint the failed component.
Will resetting the dishwasher clear the 7-7 error code?
A reset may temporarily clear the 7-7 code, but it will return if the underlying problem with the flowmeter or its wiring has not been corrected. Resetting does not fix a failed flowmeter switch or a loose connection. The fault needs to be diagnosed and the defective component repaired or replaced before the dishwasher will operate reliably.
How much does it cost to repair a Whirlpool dishwasher 7-7 error?
Repair costs depend on which component has failed. A flowmeter assembly replacement is generally the less expensive fix, with parts typically ranging from around $30 to $80 depending on the specific model. A control board replacement is significantly more costly, with parts often ranging from $100 to $250 or more. Adding professional labor will increase the total cost for either repair.
Can I fix a Whirlpool dishwasher 7-7 error myself?
Some steps are accessible to a knowledgeable DIYer. Start by disconnecting power and checking the wiring connections at both the flowmeter and the salt level sensor for looseness or corrosion. If connections are secure, the diagnostic process requires a multimeter and the ability to run a service diagnostics cycle, which is more involved. Replacing the flowmeter assembly or control board requires comfort working with appliance electrical components.
Is it safe to use my dishwasher when the 7-7 code is showing?
It is not recommended to continue using the dishwasher while the 7-7 code is active. The flowmeter plays a role in measuring water flow, and operating without a functioning flowmeter signal means the control board cannot properly monitor the wash cycle. This could result in incomplete cycles or other operational issues. Resolving the fault before resuming normal use is the safest course of action.
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass