Model reference
Whirlpool WDF730PAYB0
Dishwasher
19 documents28 error codes8 service modes
Available documentation
Tech Sheet
- Tech Sheet - W10350141 - Rev B (FR)2 pg
- Tech Sheet - W10350140 - Rev B2 pg
- Whirlpool Dishwasher WDT910SAYM0 Tech Sheet2 pg
Service Manual
- Global Wash System 2011 Undercounter Dishwashers Technical Education98 pg
Service Flash
- Installation Pointer - W10484438 (Gap Between Door and Console)6 pg
- Remove & Install Door Panel/console Ass'y3 pg
- TESTING THE GWS WASH MOTOR - Technical Service Pointer W105089109 pg
- Single Pvc Toe/kick Panel and Plastic Retention Clips4 pg
- PLASTIC TALL TUB UNDERCOUNTER DISHWASHER Metal Strike Plate and Door Seal Kit3 pg
Bulletin
- Whirlpool Dishwasher Global Wash System Service Update10 pg
Tech Tip
- Instruction Sheet2 pg
- quickreferenceinsertsheet-w10164331-reva-sp.pdf1 pg
- Installation Instructions6 pg
Other
- Whirlpool Dishwashers Self actuated latch blocks door from closing W10460578A9 pg
- Whirlpool Dishwasher WDT910SAYE0 WDT910SAYH0 WDT910SAYM0 Users Manual W1035035940 pg
- Service Pointer - W10460578 - Rev B (Latch Blocks Door From Closing)_W104605789 pg
- W10460578B9 pg
Installation Guide
- Installation Instructions48 pg
- Instruction Sheet2 pg
MyPros+ Max
Diagnose your Whirlpool WDF730PAYB0.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (28)
CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Stuck key or short circuit(s) in keypad or in control's input lines that read…10-1Dispenser electrical problem10-2Vent wax motor electrical problem10-3Drying fan error2-1Damaged or corrupted memory on control board or incompatible software…2-2Software or hardware incompatibility problem with control (User Interface).3-1Open or faulty temperature sensor, faulty temperature sensor input on control…3-2Shorted connection or component in Temperature Sensing Circuit, shorted or…3-3OWI sensor failure or failed calibration.4-3Control detected error with wash motor; motor not running.5-1Door switch stuck open5-2Door switch stuck on6-1Low/no water (mechanical problem)6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Thermistor/OWI sensor problem detected during fill.6-8Disconnected or damaged flowmeter or salt level sensor problem (water softener…7-1Heater circuit problem7-2Faulty heater drive circuit on the control or heater circuit short.7-7Flowmeter problem8-1Drain motor problem8-2Faulty drain motor drive circuit on the control or drain motor…8-3Drain motor stuck on9-1Diverter sensor or motor circuit problem9-2Faulty diverter drive circuit on the control or mechanical binding of diverter…9-3Diverter disc in sump is missing.Service modes (8)
- Clear Customer Error HistoryDuring Service Diagnostics Cycle interval 20, press Hi Temp key when Hi Temp LED is on during the…
- Error Code Reading (during Service Diagnostics)After entering Service Diagnostics Cycle
- Error Code Reading (within Service Diagnostics)After entering Service Diagnostics Cycle, interval 25 is display test (all LEDs on). Intervals…
- Rapid Advance (during Service Diagnostics)Press the Start/Resume key to advance 1 interval at a time during the Service Diagnostics Cycle.
- Rapid Advance ModePress HI TEMP
- Rapid Advance Mode (during normal cycle)Press HI TEMP
- Service Diagnostic CycleRefer to Tech Sheet provided with the dishwasher for specific entry sequence
- Service Diagnostics Cycle1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass