mypros+
Model reference

Amana OH-168-4

Furnace

12 documents26 error codes20 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W102388502 pg
    Covers this model

Installation Guide

  • Installation Instructions12 pg
    Covers this model
  • Installation Instructions64 pg
    Covers this model
  • Installation Instructions35 pg
    Covers this model
  • Installation Instructions72 pg
    Covers this model
  • Instrucciones de instalacion30 pg
    Covers this model
  • Installation Instructions24 pg
    Covers this model
  • Installation Instructions20 pg
    Covers this model
  • Installation Instructions88 pg
    Covers this model
  • Installation Instructions64 pg
    Covers this model
  • Installation Instructions140 pg
    Covers this model
  • Installation Instructions12 pg
    Covers this model
MyPros+ Max

Diagnose your Amana OH-168-4.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (26)

CodeMeaning
d13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorF01MCC (Central Control Module) communication errorF04Accelerometer component failed; the X, Y, and Z limits are outside of the…F11Motor Control Module (MCM) failureF20No water entry detectedF21Excessive drain timeF22Door lock errorF24Water temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between MCC and MCM.F29Motor overheating detected.F30Not explicitly described in the extracted text, appears in the error code table…F31Not explicitly described in the extracted text, appears in the error code table…F33Pump disconnectedF34Load detected in the washer during the washer cleaning cycle.F70Communication failure between MCC and User Interface (UI).F73User Interface (UI) failureF74User Interface (UI) failureLED1 blinkRC (Refrigerator Compartment) thermistor failure detected during service…LED2 blinkEvaporator thermistor failure detected during service diagnostics.LED3 blinkFC (Freezer Compartment) thermistor failure detected during service diagnostics.

Service modes (20)

  • Cycle Credit["Enter Washer Diagnostic Mode (display flashing).","Press the HOT button (CC will display)."]
  • Diagnostic Mode (Blink Mode)["First access Setup/Configuration Mode.","Press DELICATES & KNITS button for 1 second while one of…
  • Help Mode["PD models
  • Help Mode (dAS mode)["Enter set-up mode.","The message dAS will appear in the display.","Press the HOT button.","Press…
  • Help Mode (Manual Communication)["Enter set-up mode.","Press the WARM button until the set-up code 2.XX is on display.","Press the…
  • Manual Overview Test["Enter Diagnostic Mode (Blink Mode).","Press WHITES button while the display is blinking."]
  • Quick Drain and Spin["Enter Diagnostic Mode (Blink Mode).","Press COLORS button while the display is blinking."]
  • Quick Overview Test["Enter Diagnostic Mode (Blink Mode).","Press WOOLENS button while the display is blinking."]
  • Quick Spin Cycle["Enter Washer Diagnostic Mode (display flashing).","Press the PERM PRESS button."]
  • Service Access Code["Press the upper left button.","Press the lower right button.","Press the upper right…
  • Service Access Code Entry["Door must be open if washer is not in fault mode.","Press the upper left button.","Press the…
  • Service Diagnostics Mode["Set Freezer Temp to lowest setting (LED 1 should be the only LED illuminated over 'Freezer…
  • Set-Up Mode (9150 Models)["Insert access door key, turn, and lift to remove access door."]
  • Set-Up Mode (9160 Models via AA1 connector)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Setup/Configuration Mode["PD models
  • Setup/Programming Mode (Model 9050)["Insert key into access door, turn and lift to remove the access door."]
  • Setup/Programming Mode (Model 9060 via connector)["Disconnect power from the washer.","Open the console and disconnect connector AA1.","Close the…
  • Washer Cleaning Program["Enter Diagnostic Mode (Blink Mode).","Press BRIGHT button while the display is blinking."]
  • Washer Cleanout Cycle["Enter Washer Diagnostic Mode (display flashing).","Press the COLORS/DELICATES button."]
  • Washer Diagnostic Mode["First enter 'Start Operating Set-Up' (set-up mode).","Press and hold the COLD button for 2…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass