Model reference
Amana OH-184-5
Furnace
9 documents72 error codes9 service modes
Available documentation
Service Manual
- ADC AD-310 Service Manual-PastProduction Industrial119 pg
- jobaid w10346831 kac 5444 pg
Tech Sheet
- Tech Sheet - W10117605A6 pg
- Tech Sheet - W10115596A6 pg
Installation Guide
- Installation Instructions64 pg
- Instrucciones de instalacion64 pg
- Installation Instructions48 pg
- Installation Instructions64 pg
- Installation Instructions48 pg
MyPros+ Max
Diagnose your Amana OH-184-5.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (72)
CodeMeaning
C-81Over temperatureC-82Over temperatureCLrNo error(s) found; no corrective action required.doorFault in main door switch, lint drawer switch circuit, motor thermal overload…dSFLFault in microprocessor heating/temperature sensing circuit (failed temperature…E0EEPROM communications error.E0 F1EEPROM communications failure.E0 F2Shorted key detected.E0 F3Oven sensor shorted.E0 F5Door and switches do not agree.E1EEPROM checksum failure.E1 F1EEPROM checksum failure.E1 F2Shorted key detected.E1 F3Oven sensor opened.E1 F5Door latch not operating.E2UL A/D error(s).E2 F1UL A/D error(s).E2 F2Shorted key detected.E2 F3BAKE/BROIL range over temperature.E2 F5Latch error during CLEAN.E3 F3CLEAN range over temperature.F-12Coil under currentF-21Supply power frequency errorF-25Stuck fan on power control board (right or left side fan, depending on which…F-36Temperature sensor is not workingF-37Temperature sensor is not workingF-40Power control board failureF-42Power supply issueF-47Power supply from power control board to User Interface is missing, or WIDE…F-56Wrong or invalid configurationView all 72 error codes
F-58Wrong or invalid configurationF-60User Interface does not workF-61Power control board does not workF0 E0No error(s) foundF1EEPROM Communications error.F1 E0EEPROM communications error.F1 E1EEPROM checksum failure.F1 E2UL A/D error(s).F1-E0EEPROM communications error.F1-E1EEPROM checksum failure.F1-E2UL A/D error(s).F2Key Tail Unplugged (3-digit displayF2 E0Shorted key / stuck key detected.F2 E1Keytail unplugged from control.F2 E2UL A/D error(s).F2-E0Shorted key detected.F2-E1Oven sensor shorted.F2-E2BAKE/BROIL range over temperature condition.F2-E3CLEAN range over temperature condition.F3Key Tail Unplugged (3-digit displayF3 E0Oven temperature sensor opened (open circuit).F3 E1Oven temperature sensor shorted.F3 E2Bake/broil range over temperature condition.F3 E3Clean range over temperature condition.F3-E0Oven sensor opened.F3-E1Oven sensor shorted.F3-E2BAKE/BROIL range over temperature.F3-E3CLEAN range over temperature.F5Oven Sensor Shorted (3-digit displayF5 E0Door latch and switches do not agree.F5 E0 (door)Door switches do not agree.F5 E1Door latch not operating (latch motor or switch failure).F5 E1 (door)Door latch not operating.F5 E2Latch error during CLEAN cycle.F5 E2 (door)Latch error during clean.F5 E3Clean range over temperature.F5-E0Door and switches do not agree.F5-E1Door latch not operating.F5-E2Latch error during CLEAN.FILLDryer is not in a ready state to accept cycle commands; may indicate dryer is…HotMicroprocessor controller has sensed an exhaust temperature exceeding 220°F…SEFLRotational sensor circuit failure indicating the tumbler basket is not rotating…
Service modes (9)
- BAKE Temperature AdjustmentPress and hold BAKE key for 5 seconds
- Bake Temperature Adjustment (Calibration)Press and hold BAKE pad for 5 seconds. Current offset is shown in 3-digit display. CAL is shown in…
- Diagnostics ModeWith oven not in cooking, broiling, or cleaning mode, press
- Last Error Code RecallPress and hold CANCEL/OFF key for 5 seconds until last error code is displayed.
- Manual Configuration Mode["This menu is accessible only during the first minutes after the cooktop is plugged in.","Step 1
- Temperature Adjustment (Calibration)Press and hold BAKE pad for 5 seconds
- Temperature Adjustment ModePress and hold BAKE key for 5 seconds
- Temperature Calibration Adjustment1. Press and hold BAKE pad for 5 seconds. Current offset (if any) is shown in 3-digit display. CAL…
- Test/Diagnostic ModeWithin 60 seconds of power up, simultaneously hold down the BAKE and CLOCK keys for 5 seconds
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana furnace models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass