mypros+
Model reference

Amana CRRL-5D

Microwave

1 document43 error codes9 service modes

Available documentation

Service Manual

  • Service Manual - R021001138 pg
    Covers this model
MyPros+ Max

Diagnose your Amana CRRL-5D.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (43)

CodeMeaning
1-1Power relay K2 stuck in closed (active) position, detected by control module.1-2Control module software problem10-1Dispenser electrical problem10-3Drying fan error2-1Stuck key detected2-2No response from user interface3-1Thermistor/soil sensor open circuit3-2Thermistor/soil sensor short circuit3-3Soil sensor (OWI) calibration failure4-3Wash motor non-operation5-1Door switch stuck open5-2Door switch stuck closed6-1No water / insufficient water level in pump (mechanical problem).6-2Fill valve electrical problem6-3Suds/air in pump6-4Overfill float switch stuck in overfill position or dishwasher not level, or…6-7Flow meter disconnected or damaged.6-8Regeneration electrical problem7-1No heat7-2Heater element stuck in active mode8-2Drain motor electrical problem8-3Drain circuit constantly powered9-1Unable to determine diverter valve position9-2Diverter valve stuck9-3Diverter disc missing9-4Lower spray arm errorF1E1Indicates a CCU (Cycle Control Unit) problem.F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; this…F3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).
View all 43 error codes
F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor has shorted; temperature above 391°F (<328 ohms).F3E5Inlet and exhaust thermistors are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; this fault code will only appear when in the…F3E7Moisture sensor strip has shorted; this fault code will ONLY appear when in the…F4E1No voltage detected at the heater relay; this fault code appears ONLY when in…F4E3Restricted/low air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F6E1Communication error from UI to CCU; communication between the CCU and UI has…F6E2Communication error from CCU to UI; communication between the CCU and UI has…LLow L2 voltage (less than 50V) detected at the CCU; displayed on models 4000…L2Low L2 voltage (less than 50V) detected at the CCU.PFPower failure occurred while the dryer was running.

Service modes (9)

  • Customer Program Fast Forward ModeAfter starting a customer program, press HI TEMP
  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS LEVEL button…
  • Error History ClearDuring the service diagnostic program at the error display interval, press the HI TEMP (high…
  • Install Diagnostics["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds: Press…
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three buttons…
  • Service Diagnostic Program1
  • Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
  • User Interface Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass