mypros+
Model reference

Caloric DCR-211-1H-OL

Dishwasher

2 documents73 error codes19 service modes

Available documentation

Tech Sheet

  • Basic Operation of Commercial Stacked Washer/dryer20 pg
    Covers this model
  • Whirlpool Dishwasher WDF760SADM0 Tech Sheet W1061005912 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCR-211-1H-OL.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (73)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory or control board, incompatible software components…10-1Dispenser electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Incoming water temperature above 167°F (75°C), or shorted connection or…3-3OWI (optical soil sensor) calibration failure.4-3Wash motor not running due to loose connection in Motor circuit and/or faulty…5-1Door stuck open5-2Door stuck closed6-1Inlet water low/no water (mechanical problem)6-2Inlet water fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Incoming water cool6-8Regen valve electrical problem7-1No heat7-1 (flowmeter)Disconnected or damaged flowmeter.7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-5Drain stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disk missingd 13Coin 2 errord 16Generation 2 debit card reader errord13Washer Coin 2 error
View all 73 error codes
d16Generation 2 debit card reader errord5Washer Coin 1 errord9Washer low voltage detection errorF 01Dryer motor control circuit errorF 04Accelerometer failureF 11MCU errorF 20No water detected entering washerF 21Long drainF 22Door lock errorF 23Dryer exhaust thermistor shorted errorF 24Temperature sensor errorF 25Tachometer errorF 26Door switch errorF 27Overflow conditionsF 28Communication failure between CCU and MCU.F 29Door unlock errorF 31Overheating of motorF 33Pump disconnectedF 34Load detected in washer during Washer Cleanout Cycle.F 70Communication failure between CCU and UIC.F 71Dryer communication failure from UIC to dryer CCUF 73UIC failure (washer) / UIC Microprocessor error (dryer)F 74UIC EEPROM errorF01Washer CCU errorF04Washer accelerometer failureF11Washer MCU errorF20Washer no water detected entering washerF21Washer long drainF22Washer door lock errorF23Dryer exhaust thermistor shorted errorF24Washer temperature sensor errorF25Washer tachometer errorF26Washer door switch errorF27Washer overflow conditionF28Washer communication failure between CCU and MCU.F29Washer door unlock errorF31Washer motor overheatingF33Washer pump disconnectedF34Washer load detected during Washer Cleanout Cycle.F70Washer communication failure between CCU and UIC.F71Dryer communication failure from UIC to dryer CCUF73Dryer UIC microprocessor errorF74Washer UIC EEPROM error.

Service modes (19)

  • Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
  • Diagnostic Mode["First enter Set-Up Mode (Start Operating Set-Up).","Press and hold the lower right (COLD) button…
  • Dryer Field Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM PRESS)…
  • Dryer Field Diagnostic Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM PRESS) button."]
  • Help Mode["Press the lower left (HOT) button while in special pricing option 2.XX (or while dAS displays if…
  • Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Service Diagnostics Cycle1
  • Set-Up Mode["Coin Payment Models
  • Set-Up Mode (Coin Payment)["Insert service switch key and turn counter-clockwise."]
  • Washer Cleanout Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center right (COLORS/DELICATES)…
  • Washer Cleanout Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center right (COLORS/DELICATES)…
  • Washer Cycle Credit["Enter Diagnostic Mode (entire display flashing).","Press the lower left (HOT) button (CC will…
  • Washer Cycle Credit (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower left (HOT) button (CC will…
  • Washer Manual Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center left (COTTON/WHITES) button."]
  • Washer Manual Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center left (COTTON/WHITES) button."]
  • Washer Quick Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (WARM) button."]
  • Washer Quick Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (WARM) button."]
  • Washer Quick Spin Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center middle (PERM PRESS) button."]
  • Washer Quick Spin Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center middle (PERM PRESS) button."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax