mypros+
Model reference

Electrolux EIDW6305GW1A

Dishwasher

7 documents16 error codes17 service modes

Available documentation

Service Manual

  • Service Data Sheet2 pg
    Covers this model
  • DISHWASHER SERVICE MANUAL - Built-in Dishwasher Models EIDW6105GS0/1, EIDW6305GS0/1, EWDW6505GS0 Technical Service Manual104 pg
    Covers this model
  • Technical Service Manual Built-in Dishwasher104 pg
    Covers this model

Bulletin

  • Dishwasher Door Drops Below 90°1 pg
    Covers this model

Service Flash

  • Getting An E01 Code On The Control1 pg
    Covers this model

Other

  • Use & Care Guide - Built-In Dishwasher72 pg
    Covers this model
  • Error Code Booklet74 pg
    Covers this model
MyPros+ Max

Diagnose your Electrolux EIDW6305GW1A.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (16)

CodeMeaning
CLClose door promptEr 01Leak detectorEr 02Thermistor/turbidity module has failed.Er 03Dead wash motor (wash pump failure).Er 04Dead drying damper.Er 05The control has not received the proper fan speed feedback from the upper fan.Er 06The control has not received the proper fan speed feedback from the lower fan.Er 07In drain mode, the control has not received proper position feedback from drain…Er 08Control has verified a switch on user interface is bad or shorted (tactile or…Er 09A communication failure between the user board and the power supply or main…Er 10Failure in the main power relay.Er 11Time out before finding a state for the drain valve.Er 12The drain valve is running when it should be off; could be a shorted component.Er 13System failureHDWater heat delay indicatorPFPower failure

Service modes (17)

  • Acceptance Test - B, C ControlPress 'Favorite' and 'Auto Wash' together. Then press
  • Acceptance Tests - A ControlPress '<' and '>' simultaneously
  • C-Relay Test - A ControlPress 'Delay Time' and 'Set' keys
  • Continuous Wash Mode - A ControlSimultaneously hold 'Delay Time' and 'Set' keys during power-up to enter diagnostics
  • Demo Mode - A ControlHold 'Select Option' and 'Right Arrow' keys for 5 seconds
  • Disable Display - A ControlPress and hold the left arrow for 10 seconds
  • Discrete Relay/Triac and Sensor Test - A ControlPress 'Delay Time' and 'Set' keys simultaneously
  • Discrete Relay/Triac and Sensor Test - B, C ControlPower on or power on reset, within 15 seconds hold simultaneously 'Sanitize' and 'Delay'. When 'Et'…
  • Display Water Temperature and Turbidity Voltages Test Mode - A ControlSimultaneously hold 'Delay Time' and 'Set' keys during power-up
  • Display Water Temperature and Turbidity Voltages Test Mode - B ControlOpen the door, select any cycle (except My Favorite), press 'Start/Cancel' key, then press and hold…
  • Engineering Tests - A ControlFrom power up or power reset mode, press 'Set' and 'Delay Start' simultaneously
  • Engineering Tests - B, C and Panel Ready ControlPress 'Sanitize' and 'Delay Start' simultaneously. 'Et' is displayed. Then press
  • Lock ControlsPress and hold the AIR DRY button for 3 seconds when the door is latched.
  • Software Version - A ControlSimultaneously hold 'Delay Time' and 'Set' keys, then select the software ID test option.
  • Software Version - B, C ControlSimultaneously hold 'Delay' and 'Sanitize' keys
  • Water Service Test - A Control (From Idle Mode)Simultaneously press the 'Wash Cycles' and 'Delay Time' keys for three seconds
  • Water/Service Test - B, C Control (From Idle Mode)Simultaneously press 'Heavy' key (B & C models) and START/CANCEL keys for three seconds

Full entry steps, exit procedures, and test sequences are available in Max.

Related Electrolux dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax