mypros+
Error code reference

Electrolux Dishwasher Error Code Er 07

Drain Valve

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Er 07 error code actually means

Your Electrolux dishwasher is showing Er 07 because the main control board tried to open or close the drain valve but did not get confirmation that the valve actually moved. This usually means the drain valve itself is stuck or broken, or there is a wiring problem between the valve and the control board. The dishwasher stopped the cycle to avoid a drainage problem.

Diagnostic procedure

The full Er 07 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Er 07 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Er 07

Ranked by how often they cause this code
  1. 1Failed Drain Valve Assembly
  2. 2Damaged or Disconnected Wiring Harness
  3. 3Corroded or Loose Connector Pins
  4. 4Foreign Object Blocking the Drain Valve
  5. 5Faulty Control Board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Er 07

What does Er 07 mean on a Electrolux dishwasher?
Er 07 means the control board did not receive proper position feedback from the drain valve during the drain cycle. The board commands the valve to open or close and expects a confirmation signal in return. When that signal is missing or incorrect, the dishwasher logs Er 07 and stops the cycle. The fault typically points to the drain valve assembly, its wiring, or connector connections.
Is it safe to use my Electrolux dishwasher when Er 07 is displayed?
You should not continue running the dishwasher with Er 07 active. The error indicates the drain valve is not operating or reporting correctly, which could lead to improper draining or water accumulating in the unit. Running cycles without resolving the fault risks water damage and may complicate the diagnosis. Address the fault before resuming normal use.
Will resetting my Electrolux dishwasher clear the Er 07 error?
A power reset may temporarily clear Er 07 from the display, but the code will return if the underlying fault is not corrected. Resetting is useful as a first step to confirm whether the fault is intermittent or persistent. If Er 07 reappears after the reset and a drain cycle, the drain valve, wiring, or control board requires physical inspection and testing to resolve the issue.
Can I fix Er 07 on my Electrolux dishwasher myself?
Some causes of Er 07 are DIY-friendly, such as clearing a debris obstruction from the drain valve area or reseating a loose connector. Wiring inspection and continuity testing require a multimeter and basic electrical knowledge. Replacing the drain valve assembly is a moderate repair that many experienced DIYers can complete. Control board replacement is more complex and may warrant professional service.
How much does it cost to repair Er 07 on an Electrolux dishwasher?
If the repair only requires cleaning connectors or clearing a blockage, costs may be minimal beyond your time. A replacement drain valve assembly typically costs in the range of $30 to $80 for parts, with professional labor adding $100 to $200 depending on your location. A control board replacement is the most expensive scenario, with parts generally ranging from $100 to $250 or more. Getting a diagnostic visit from a technician before ordering parts is recommended.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass