mypros+
Error code reference

Electrolux Dishwasher Error Code Er 02

Thermistor

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Er 02 error code actually means

Your Electrolux dishwasher is showing Er 02 because it cannot get a proper reading from the sensor that monitors water temperature and water cleanliness during the wash cycle. This means the dishwasher cannot run its cycles correctly and has stopped as a safety measure. The sensor or its wiring connection has likely failed and will need to be inspected or replaced.

Diagnostic procedure

The full Er 02 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Er 02 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Er 02

Ranked by how often they cause this code
  1. 1Failed thermistor/turbidity module
  2. 2Loose or corroded wiring connector
  3. 3Damaged wiring harness
  4. 4Mineral or debris buildup on the sensor
  5. 5Failed control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Er 02

What does Er 02 mean on a Electrolux dishwasher?
Er 02 indicates that the dishwasher's thermistor or turbidity module has failed or is sending a signal the control board cannot interpret. The thermistor monitors water temperature and the turbidity sensor measures water cleanliness during the wash cycle. When this sensor assembly malfunctions, the dishwasher stops operating and displays Er 02 to alert you to the fault.
Is it safe to use my Electrolux dishwasher with an Er 02 error?
You should not continue running the dishwasher while Er 02 is active. Because the thermistor monitors water temperature, a failed sensor means the control board cannot properly regulate the heating element during the wash cycle. Running the appliance without reliable temperature control could result in overheating or inadequate cleaning, and the dishwasher will typically refuse to complete a cycle anyway until the fault is resolved.
Will resetting the dishwasher clear an Er 02 error?
A reset may temporarily clear the displayed code, but if the thermistor or turbidity module has genuinely failed, the error will return as soon as the dishwasher attempts to read the sensor again. Resetting can be a useful first step to confirm whether the fault is intermittent or persistent, but it does not address the underlying hardware problem. A proper repair of the sensor or wiring is needed for a permanent fix.
Can I fix an Er 02 error myself?
Some causes of Er 02 are DIY-accessible, such as reseating a loose wiring connector or cleaning debris from the sensor. If the sensor module itself has failed, replacing it requires basic disassembly of the dishwasher interior and comfort working with appliance wiring. Technicians with appliance repair experience can typically handle this repair, but if you are unsure about working with electrical components, hiring a professional is the safer choice.
How much does it cost to repair an Er 02 error on an Electrolux dishwasher?
If only the thermistor or turbidity module needs replacement, parts typically range from around $20 to $80 depending on the specific model. If professional labor is included, total repair costs generally fall in the $100 to $250 range. A failed control board, if that turns out to be the root cause, would increase costs significantly.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass