Model reference
GE PDTSS_F
Dishwasher
18 documents55 error codes41 service modes
Available documentation
Service Manual
- Technical Service Guide - Dishwasher97 pg
- Technical Service Guide97 pg
- GE Appliances Technician's Manual GE Built-in Dishwashers Generation II14 pg
- GE Profile™ Dishwasher Technical Service Guide37 pg
- Manuel du propriétaire - Lave-vaisselle GE Profile24 pg
- TECHNICAL SERVICE GUIDE Top Control Profile Dishwashers27 pg
- Technical Service Guide "2" Model Dishwashers31 pg
- TECHNICAL SERVICE GUIDE Profile Dishwashers34 pg
- GE Appliances Technical Service Guide - GE and Profile Dishwashers PermaTuf® Tub Models and Stainless Steel Tub Models40 pg
- GE and Profile Dishwashers Technical Service Guide40 pg
- GE and Profile Dishwashers PermaTuf Tub and Stainless Steel Tub Technical Service Guide40 pg
- GE Consumer & Industrial Technical Service Guide - GE Profile Dishwasher PDW8900 Series, PDW9700 Series, PDW9900 Series37 pg
- GE Profile TM Dishwasher Technical Service Guide37 pg
- TECHNICAL SERVICE GUIDE Profile Dishwashers35 pg
- GE Profile Dishwashers Owner's Manual48 pg
- GE Profile Dishwashers Owner's Manual16 pg
- Dishwashers Triton™ Profile™ Owner's Manual32 pg
Training
- TECHNICAL SERVICE GUIDE MODEL DISHWASHERS Profile Performance Series31 pg
MyPros+ Max
Diagnose your GE PDTSS_F.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (55)
CodeMeaning
ALL_FLASH_BEEPControl error indicated by all status lights (SENSING, WASHING, RINSING…C1Slow drain fault detected; pump out time is over 100 seconds.C2Pump out time is more than 400 seconds; control stops the pump for 5 seconds…C3Control does not sense the drain feedback signal; control will default to…C4Control detects a flood condition within the dishwasher; control will beep at 1…C5Control detects two consecutive pump out times of less than 6 seconds…C6Water temperature did not reach 120°F during the main wash; fault continues to…C7Control checks the temperature sensor at start of each wash cycle to determine…CLEAN flashingUnit has no water; the water supply may be off or there is a water supply issue.CLEAN flashing (alone)Unit has no waterDRYING FLASHINGControl error on Profile Performance models indicated by flashing DRYING LED…F0Turbidity sensor failureF1Turbidity sensor failureF112Key stuck on UI control.F128Low rinse aid level detected.F144Replace inverter.F145Check AC volts to inverter.F146Replace circulation pump.F147Replace drain pump.F148Replace motor with faulty TCO.F149Check harness or inverter.F16High water temperature detected.F2Communication failed between main board and UI control.F3Configuration errorF33Door switch error.F34Leak pan detected errorF35Diverter feedback error.F4Turbidity sensor failureF48Turbidity sensor reading high.F49Turbidity sensor reading low.View all 55 error codes
F5Communication failed with inverter.F50Temperature sensor reading high.F51Temperature sensor reading low.F52Turbidity sensor calibration failure.F64Inverter error received.F65Inverter no water detected.F80Absent water flow (turbidity based).F96No water in tub (turbidity based).F97Absent heat source detected.F98Non-draining sump (turbidity based).F99Minimum wash temperature not met.Lock LED + continuous beepFactory Test Mode calibration failureLOCK LED illuminated + continuous beeping (Factory Test Mode)Turbidity sensor check has failed during factory test mode; control module…NORMAL FLASHINGControl error on Profile models indicated by flashing NORMAL LED and beeping…PFElectrical power has been interrupted to the dishwasher; PF comes up in the…RINSING FLASHINGControl error on Profile Performance models indicated by flashing RINSING LED…RINSING_FLASHControl error indicated by the RINSING status light flashing along with a…SENSINGCleanSensor errorSensing LED not litTurbidity sensor circuit has failed open or is shorted; unit will operate for…SENSING OFFCleanSensor errorSTART RESET FLASHINGNormal indication on Profile models that the START/RESET pad has been pressed…START/RESET flashingCycle has been interrupted by pressing the START/RESET keypad; light will quit…START/RESET flashing + CLEAN flashingCycle has been interrupted by pressing the START/RESET keypad; light will quit…WASHING FLASHINGSTART/RESET pad has been pressed on Profile Performance models, indicating the…WASHING_RINSING_FLASHSTART/RESET pad has been pressed
Service modes (41)
- Consumer Purge Cycle1. Make sure Pre-wash, Added Heat, and Heated Dry LEDs are off. 2. Press Heated Dry pad and…
- Control lock["Press and hold HEATED DRY button for 3 seconds
- Control Panel Lock/Unlock["Press and hold the HEATED DRY pad for 3 seconds to lock the controls (light above LOCK pad will…
- Control Replacement/Calibration (test/00 calibration mode)["The dishwasher will enter into the test/00 calibration mode when the unit is first powered…
- control_replacement_calibrationThe dishwasher will enter into the test/00 calibration mode when the unit is first powered on
- Demo ModePress the Cookware pad (Down arrow on Top Control models) and Added Heat pad simultaneously for 5…
- Diagnostic Fault Code Display ModeWith the dishwasher in Standby Mode (Cycle Selection Mode), press and hold the Cycle Select and…
- End-of-cycle beep toggle["Press HEATED DRY button 5 times within 3 seconds.","Three beeps will sound to indicate the…
- F.I Test (Smart Models)["1
- F.I Test (Value Models)["1
- F1 Test Cycle["Close detergent cup and add hot water.","Press POTS & PANS and NORMAL WASH keypads at the same…
- F1 Test Freeze Capability["While F1 test cycle is running, press the HEATED DRY keypad to pause on the current test…
- Factory Test ModeDisconnect power from dishwasher
- Factory Test Mode (Front Control)["Enter Service Mode.","Press Key#5 and Key#1 together for 3 seconds.","This sets auto FE Entry…
- Factory Test Mode (Top Control)["Enter Service Mode.","Press Heated Dry and Delay Hours together for 3 seconds.","This sets auto…
- factory_test_mode_entry_flagFront control models
- Fast Control Model Reset["Make sure the unit is powered off.","Press and hold the Start/Reset keypad and power the unit…
- fast_control_model_reset1
- Freeze Capability (during F.I Test)["During the F.I test cycle, press the LOCK pad to pause.","Press any pad to continue."]
- LOW DETERGENT indicator toggle["Press ADDED HEAT button 5 times within 3 seconds.","Three beeps will sound and the LOW DETERGENT…
- Service ModePDW8900 Series
- Service Mode (Load Control)1
- Service Test Mode["Put the dishwasher in standby mode.","On front control models, press Key#8 and Key#4…
- service_test_mode1
- SmartDispense Water Hardness Calibration["Close and latch the door (lights on, dishwasher not running).","Press the COOKWARE and DELAY…
- SmartDispense water hardness calibration (12-button front panel with 3-digit display)["Close and lock the door (lights on, dishwasher at rest).","Press COOKWARE and DELAY HOURS buttons…
- SmartDispense Water Hardness Calibration (12-Button Front-Control Models With 3-Digit Display)["Close and latch the door (lights on, dishwasher not running).","Press the COOKWARE and DELAY…
- SmartDispense water hardness calibration (7-button front panel with 3-digit display)["Open the door and press any button (other than START) to activate the lights.","Press Up arrow…
- SmartDispense Water Hardness Calibration (7-Button Front-Control Models With 3-Digit Display)["Open the door and touch a pad (other than START) to turn lights on.","Press the Up Arrow Pad and…
- SmartDispense water hardness calibration (models without 3-digit display, front controls)["Close and lock the door (lights on, dishwasher at rest).","Press COOKWARE and DELAY HOURS buttons…
- SmartDispense water hardness calibration (models without 3-digit display, top controls)["Open the door and press any button to activate the lights.","Press Up arrow and DELAY HOURS…
- SmartDispense Water Hardness Calibration (Models Without a 3-Digit Display - Front Controls)["Close and latch the door (lights on, dishwasher not running).","Press the COOKWARE and DELAY…
- SmartDispense Water Hardness Calibration (Models Without a 3-Digit Display - Top Controls)["Open the door and touch a pad to turn lights on.","Press the Up Arrow Pad and DELAY HOURS pad at…
- Toggle End-of-Cycle Audible Signal["Press the HEATED DRY pad 5 times within 3 seconds.","A triple beep will sound to indicate the…
- Toggle LOW DETERGENT LED (when not using SmartDispense)["Press the ADDED HEAT pad 5 times within 3 seconds.","You will hear 3 beeps; then the light will…
- Turbidity Sensor CalibrationMust be entered within 2 minutes of power up
- Water Hardness Calibration ModePDW8900
- Water Hardness Calibration Mode - Front Mount Control (PDW8900)["Dishwasher must be in standby mode
- Water Hardness Calibration Mode - Top Mount Control (PDW9700, PDW9900)["Dishwasher must be in standby mode.","Press up arrow to wake up control and illuminate the lights…
- Water Hardness Calibration Mode (PDW8900)Dishwasher in standby mode with door closed and latched
- Water Hardness Calibration Mode (PDW9700/PDW9900)Dishwasher in standby mode
Full entry steps, exit procedures, and test sequences are available in Max.
Related GE dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass