mypros+
Model reference

GE GFDN245

Dryer

9 documents22 error codes24 service modes

Available documentation

Service Manual

  • Technical Service Guide53 pg
    Covers this model
  • GE Appliances Technical Service Guide53 pg
    Covers this model
  • GE HA Dryer With Mist Service Manual53 pg
    Covers this model
  • GE HA Dryer With Mist Service Guide53 pg
    Covers this model
  • Dryers Owner's Manual60 pg
    Covers this model
  • Technical Service Guide - UltraFresh Dryer59 pg
    Covers this model

Bulletin

  • Squeaking Dryer2 pg
    Covers this model

Training

  • GE HA Dryer With Mist Technical Service Guide53 pg
    Covers this model

Other

  • 319209DryerwithMistGFDNGFDS53 pg
    Covers this model
MyPros+ Max

Diagnose your GE GFDN245.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (22)

CodeMeaning
1Inlet thermistor failure10Empty drum detection tripped11Blocked vent13Door switch signal stuck closed14Door latch pulsing error15Critical flood level by gallons19Door latch lost in run2Outlet thermistor failure6Stuck button8Door latch stuck9Dry load detection tripE00No errors in the fault log.E1Interface EEPROM reading or writing improperly.E11Drum motor is not rotating properly or centrifugal switch is bad.E14Stuck button/keys detected.E2Power EEPROM reading or writing improperly.E3Inlet thermistor shorted.E4Inlet thermistor open.E5Outlet thermistor shorted.E6Outlet thermistor open.E7Check electrical connectionE8Power model selector error on power board.

Service modes (24)

  • Consumer Fault Code ModeFrom an idle state only (all LEDs off), press and hold the Start pad for 10 seconds
  • Demo Mode1
  • Service ModeFrom an idle state (all LEDs off) or from a standby state (LEDs on but no cycle running), press and…
  • Service Test ModeFrom idle state, press and alternate between the 'My Cycle' and 'Delay Start' buttons
  • Service Test T01 - Error Codes["Enter Service Test Mode.","Select T01 using the knob.","Press START/PAUSE to display error…
  • Service Test T02 - Version Info["Enter Service Test Mode.","Select T02 using the knob.","Press START/PAUSE to display the current…
  • Service Test T03 - EEPROM Check["Enter Service Test Mode.","Select T03 using the knob.","Press START/PAUSE
  • Service Test T04 - UI Test["Enter Service Test Mode.","Select T04 using the knob.","Press START/PAUSE.","The control turns on…
  • Service Test T05 - Outlet Thermistor["Enter Service Test Mode.","Select T05 using the knob.","Press START/PAUSE.","The control displays…
  • Service Test T06 - Inlet Thermistor["Enter Service Test Mode.","Select T06 using the knob.","Press START/PAUSE.","The control displays…
  • Service Test T07 - Moisture Sensor["Enter Service Test Mode.","Select T07 using the knob.","Press START/PAUSE.","The control displays…
  • Service Test T08 - Steam Test["Enter Service Test Mode.","Select T08 using the knob.","Press START/PAUSE.","Control displays…
  • T01 - Error CodesIn service mode, select T01 using the knob, then press Start/Pause to display error codes
  • T01 - Error Codes TestIn service mode, select T01 and press Start/Pause
  • T02 - Version InfoIn service mode, select T02 using the knob, then press Start/Pause. Displays current UI SW version…
  • T03 - EEPROM CheckIn service mode, select T03 using the knob, then press Start/Pause
  • T04 - UI TestIn service mode, select T04 using the knob, then press Start/Pause
  • T05 - Outlet ThermistorIn service mode, select T05 using the knob, then press Start/Pause
  • T05 - Outlet Thermistor TestIn service mode, select T05 and press Start/Pause
  • T06 - Inlet ThermistorIn service mode, select T06 using the knob, then press Start/Pause
  • T06 - Inlet Thermistor TestIn service mode, select T06 and press Start/Pause
  • T07 - Moisture SensorIn service mode, select T07 using the knob, then press Start/Pause
  • T07 - Moisture Sensor TestIn service mode, select T07 and press Start/Pause
  • T08 - Steam TestIn service mode, select T08 using the knob, then press Start/Pause

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE dryer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass