Model reference

GE GFDS

Name: GE GFDS
Brand: GE

Dryer

3 documents34 error codes22 service modes

Available documentation

Service Manual

GE HA Dryer With Mist Service Guide53 pg
Covers this model
GE Dryer GFDN1E GFDS GFMN GFMS GMMN Mini Manual2 pg
Covers this model
Technical Service Guide - UltraFresh Dryer59 pg
Covers this model

MyPros+ Max

Diagnose your GE GFDS.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·GE Dryer

1 on my GE GFDS

M+

Inlet thermistor failure — thermistor

From Service Manual 464272, p.44:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WR55X10025

Temperature sensor

Error codes (34)

CodeMeaning

1Inlet thermistor failure 10Empty drum detection tripped 11Blocked vent 13Door switch signal stuck closed 14Door latch pulsing error 15Critical flood level by gallons 19Door latch lost in run 2Outlet thermistor failure 6Stuck button 8Door latch stuck 9Dry load detection trip E00General error affecting all systems.E01EEPROM read/write problem.E02Inlet thermistor shorted.E03Outlet thermistor shorted.E04Inlet thermistor open circuit.E05Outlet thermistor open circuit.E06Different EEPROM detected; UI type stored in EEPROM does not match physical UI…E07A button is stuck in the low/pressed position.E1Interface EEPROM reading or writing improperly.E11Drum motor is not rotating properly or centrifugal switch is bad.E14Stuck keys detected on control panel.E2Power EEPROM reading or writing improperly.E3Inlet thermistor shorted.E4Inlet thermistor open.E5Outlet thermistor shorted.E6Outlet thermistor open.E60Door switch is open.E61Control board miswired; L2 and N are miswired (AC input too high).E62Control board input error; AC line frequency detection error and low input…

View all 34 error codes

E7Miss wire E8Power model selector error on power board.E80Invalid UI model configured on control board.E81Invalid Power model configured on control board.

Service modes (22)

Consumer Fault Code ModeFrom an idle state only (all LEDs off), press and hold the Start pad for 10 seconds
Demo Mode1
Service ModeFrom an idle state (all LEDs off) or from a standby state (LEDs on but no cycle running), press and…
Service Test ModeFrom idle state, press and alternate between the 'My Cycle' and 'Delay Start' buttons
T01 - Error Codes TestIn service mode, select T01 and press Start/Pause
T01 - UI ConfigurationSelect T01 in service mode and press Start/Pause
T02 - Error CodesSelect T02 in service mode and press Start/Pause
T02 - Version InfoIn service mode, select T02 and press Start/Pause. Displays current UI SW version. Turn knob CW to…
T03 - EEPROM CheckIn service mode, select T03 and press Start/Pause
T03 - Version InfoSelect T03 in service mode and press Start/Pause
T04 - EEPROM CheckSelect T04 in service mode and press Start/Pause
T04 - UI TestIn service mode, select T04 and press Start/Pause
T05 - Outlet Thermistor TestIn service mode, select T05 and press Start/Pause
T05 - UI TestSelect T05 in service mode and press Start/Pause
T06 - Inlet Thermistor TestIn service mode, select T06 and press Start/Pause
T06 - Keys ContinuitySelect T06 in service mode and press Start/Pause
T07 - Moisture Sensor TestIn service mode, select T07 and press Start/Pause
T07 - Outlet ThermistorSelect T07 in service mode and press Start/Pause
T08 - Inlet ThermistorSelect T08 in service mode and press Start/Pause
T08 - Steam TestIn service mode, select T08 and press Start/Pause
T09 - Moisture SensorSelect T09 in service mode and press Start/Pause
T10 - Steam TestSelect T10 in service mode and press Start/Pause

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE dryer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass