mypros+
Error code reference

GE Dryer Error Code E05

EEPROM CRC fault

GE codesGE dryer codes

EEPROM CRC fault – bad CRC (Cyclic Redundancy Check) detected when reading a page from EEPROM.

First step from the service manual

Check and replace user interface board if necessary.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E05.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E05 means on a GE dryer

The E05 error code on a GE dryer indicates an EEPROM CRC (Cyclic Redundancy Check) fault. The EEPROM (Electrically Erasable Programmable Read-Only Memory) is a small non-volatile memory chip that stores operational settings, calibration data, and cycle configuration for the control system. During normal operation, the control board reads data from specific pages of the EEPROM and verifies its integrity using a CRC algorithm. When the calculated checksum does not match the stored checksum for a given memory page, the control flags an E05 fault and typically halts operation to prevent running with corrupted settings.

The EEPROM is either embedded within the user interface board or closely tied to it. A bad CRC result can stem from data corruption within the chip itself, which may occur due to power surges, voltage spikes, or repeated incomplete write cycles over the appliance's lifespan. In some cases, a manufacturing defect or age-related degradation of the memory cells can cause individual bits to flip, producing an invalid checksum on readback.

Because the EEPROM data is integral to how the control system configures and runs cycles, a corrupted memory page can prevent the dryer from operating correctly. The primary diagnostic step is to inspect and replace the user interface board, since this component houses or directly interfaces with the EEPROM. In some instances, a power reset may temporarily clear the fault if the corruption was transient, but recurring E05 codes almost always indicate a hardware failure requiring board replacement.

Source: manufacturer service documentation.

Common causes of E05

  1. 01

    Failed or corrupted user interface board

    Part replacement

    The EEPROM on the user interface board may have developed corrupted memory cells due to age, voltage irregularities, or component wear. This is the most direct cause of a CRC mismatch and replacement of the board is the primary recommended fix.

  2. 02

    Power surge or voltage spike

    Wiring / connection

    A sudden surge in power can corrupt data written to the EEPROM during an interrupted write cycle. If the E05 code appeared shortly after a power outage or electrical event, a surge is a likely contributing factor.

  3. 03

    Loose or intermittent wiring connections

    Wiring / connection

    Poor electrical connections between the user interface board and the main control board can cause unreliable data communication, potentially triggering a CRC error. Inspect connector pins and harness connections for corrosion, looseness, or damage.

  4. 04

    Aging or worn EEPROM memory cells

    Part replacement

    EEPROM chips have a finite number of read and write cycles. On older dryers, the memory cells can degrade over time and begin producing read errors. This typically results in persistent, non-clearing E05 faults.

See the test procedure for each cause

Frequently asked questions about E05

What does E05 mean on a GE dryer?
E05 on a GE dryer indicates an EEPROM CRC fault, meaning the control system detected corrupted or invalid data when reading a page from the dryer's internal memory chip. The CRC (Cyclic Redundancy Check) is a verification process that confirms stored data is intact. When the check fails, the dryer flags the fault to prevent operating with bad settings. The user interface board, which houses or communicates with the EEPROM, is the primary component to inspect.
Can I fix the E05 error on my GE dryer myself?
A DIYer with basic appliance repair experience can attempt to resolve E05 by first performing a power reset: unplug the dryer for several minutes and restore power to see if the fault clears. If the code returns, the user interface board will likely need to be replaced, which involves disconnecting the wiring harness and swapping the board. If you are not comfortable working with appliance electronics, a professional technician is recommended.
Will resetting my GE dryer clear the E05 error code?
A power reset may temporarily clear E05 if the EEPROM corruption was caused by a one-time event such as a power interruption. However, if the memory chip itself is damaged or degraded, the fault will return after the control attempts to read that memory page again. Persistent or recurring E05 codes after a reset almost always point to a hardware failure requiring board replacement.
Is it safe to use my GE dryer when it shows E05?
The E05 fault typically prevents the dryer from completing a cycle or operating normally, which means the dryer itself is limiting use until the issue is addressed. Running any appliance with a corrupted control memory is not advisable, as settings governing heat levels and cycle timing may be unreliable. It is best to resolve the fault before returning the dryer to regular use.
How much does it cost to repair an E05 error on a GE dryer?
If the repair requires a new user interface board, parts alone typically range from around $50 to $200 or more depending on the specific model. If you hire a technician, total repair costs including labor generally fall in the range of $150 to $350. A power reset costs nothing and is always worth attempting first before purchasing parts.

Related GE dryer codes

All GE dryer codes
View all 159 GE dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass