Model reference

GE WPGT9350

Name: GE WPGT9350
Brand: GE

Washer

8 documents19 error codes5 service modes

Available documentation

Service Manual

GE Washer WPGT9350 Mini Manual1 pg
Covers this model
TECHNICAL SERVICE GUIDE - Profile Washer WPGT935059 pg
Covers this model
Profile Washer Technical Service Guide59 pg
Covers this model
GE Consumer Products TECHNICAL SERVICE GUIDE Profile Washer59 pg
Covers this model
WPGT9350 Technical Service Guide59 pg
Covers this model
TECHNICAL SERVICE GUIDE Proﬁle Washer59 pg
Covers this model

Training

Appliance Diagnostic Modes Laundry128 pg
Covers this model

Other

GE Harmony Washer64 pg
Covers this model

MyPros+ Max

Diagnose your GE WPGT9350.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·GE Washer

Basket doesn't stop fast enough on my GE WPGT9350

M+

Applying the brake to the basket has

From Service Manual 176467, p.39:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WR55X10942

Main control board

Error codes (19)

CodeMeaning

Basket doesn't stop fast enoughApplying the brake to the basket has failed to stop within 10 seconds.Brake Resistor failedThe voltage across the brake resistor is unsuitable; brake resistor has failed.Broken Clutch CouplingBasket was detected as slowing down too quickly, indicating a broken clutch…ClutchHome position signal from the clutch motor has not been detected after three…COM ERRORInternal serial communication self-diagnostic test on the main board has failed…Drain SystemWater remains in the tub after the drain pump has been activated; unit is not…Flash ROMChecksum errors found; data is not being written/controlled correctly in EEPROM.Flood Condition Stage 1Water level exceeded expected level during fill; possible flood detected.Inverter not operating correctlyInverter board temperature has exceeded the minimum temperature limit by more…Keypanel MembraneA keypanel membrane pad was detected as pressed for longer than 30 seconds.LCD Display TouchScreenAn LCD touchscreen input was detected for an extended period (longer than 30…Lid Switch Stuck ClosedLid switch appears stuck in closed position; washer cannot detect that lid has…Lid Switch Stuck OpenLid switch appears stuck in open position; washer continuously displays 'Please…Main / Inverter Control ErrorInverter board failed to report to the main board 3 times in a row…Motor not rotating properlyMotor is not turning within 50% of the desired speed or is rotating in only one…No Fill or Slow FillWater is not dispensing into unit properly; fill not detected or too slow.Pressure SensorPressure sensor signal is outside the acceptable frequency range (approximately…Serial Washer Dryer ConnectorSerial communication between washer and dryer failed; washer has not received…ThermistorThermistor reading is out of range; unit defaults to cold water.

Service modes (5)

Factory Test Mode1
Field Service Mode1
Sales Demo ModePress HOME and MY CYCLES simultaneously for 3 seconds.
Setup/Self Diagnostic ModeAutomatically runs when power is reconnected after exiting Field Service Mode (after error codes…
Troubleshooting ModeFrom Home Screen, press START/STOP and MY CYCLES simultaneously for 3 seconds, then press…

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass