Model reference

Jenn-Air JDB9000CWP1

Dishwasher

6 documents31 error codes8 service modes

Available documentation

Tech Sheet

Tech Sheet - W10580767 - Rev C (FR)16 pg
Covers this model
Tech Sheet12 pg
Covers this model
Fiche technique W10751168C16 pg
Covers this model

Service Manual

Kenmore Elite 2013 Stainless Steel Tall Tub Dishwashers82 pg
Covers this model

Installation Guide

Instruction Sheet1 pg
Covers this model

Other

technicalreferencemanual 2211031382 pg
Covers this model

MyPros+ Max

Diagnose your Jenn-Air JDB9000CWP1.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Jenn-Air Dishwasher

1-1 on my Jenn-Air JDB9000CWP1

M+

Control detected K2 pilot relay stuck

From Tech Sheet W10905698, p.30:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (31)

CodeMeaning

1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem 10-2Vent wax motor electrical problem; loose connection in vent circuit and/or open…10-3Drying fan error 2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control; loose user interface…3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Incoming water temperature above 167°F (75°C), or shorted connection/component…3-3OWI calibration failure 4-3Wash motor not running due to loose connection in Motor circuit and/or faulty…4-4Wash motor failure; loose connection in wash motor circuit and/or open wash…5-1Door stuck open 5-2Door stuck closed 6-1Low/no water 6-2Fill valve electrical problem 6-3Suds or air in pump 6-4Float switch open 6-6Incoming water under 84°F (29°C)6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem 7-1No heat 7-2Heater stuck on 8-1Slow drain 8-2Drain motor electrical problem 8-3Drain stuck on 8-4Drain motor electrical problem; loose connection in drain motor circuit and/or…9-1Diverter can't find position 9-2Diverter stuck on 9-3Diverter disk missing

View all 31 error codes

9-4Lower spray arm error; mechanical binding or blocking of spray arm; corroded or…

Service modes (8)

clear_error_historyDuring diagnostic program interval 22, press Hi Temp key to clear customer error history. If Hi…
customer_program_fast_forwardAfter starting a customer program, press HI TEMP
diagnostic1
Rapid Advance (Customer Cycles)["Start a customer cycle.","Press HIGH TEMP
Rapid Advance Mode (during active cycle)After starting a cycle, press HI TEMP
Sales Demo Mode ClearRun Service Diagnostics Cycle to clear demo mode.
Service Diagnostic CycleWith dishwasher in standby, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more than…
Service Diagnostics Cycle["Press Start key to wake up the control panel.","Press any 3 keys in the sequence…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass