mypros+
Model reference

Jenn-Air JJW9530DDW

Oven

12 documents48 error codes29 service modes

Available documentation

Tech Sheet

  • Electric Wall Oven Technical Information10 pg
    Covers this model
  • Tech Sheet - 160225099 pg
    Covers this model

Service Manual

  • Service Manual - Electric Wall Ovens37 pg
    Covers this model
  • Failure Codes and Wiring Diagrams for Maytag Heritage Gas & Electric Ranges124 pg
    Covers this model
  • Electric Wall Oven Service Manual60 pg
    Covers this model
  • FAILURE CODES AND WIRING DIAGRAMS for MAYTAG HERITAGE GAS & ELECTRIC RANGES124 pg
    Covers this model

Bulletin

  • Technical Bulletin - TDC-0068B-B Hinge and Receptacle Modification2 pg
    Covers this model
  • Technical Bulletin - Hinge and Receptacle Modification2 pg
    Covers this model

Service Flash

  • TechnicalBulletin - TDC-0104-B - Center Oven Temperature in Bake_TDC-0104-B1 pg
    Covers this model
  • Service Update First HALF—200994 pg
    Covers this model
  • Repair Tip - Hinge and Receptacle Modification2 pg
    Covers this model

Other

  • JJW9527DDS9 pg
    Covers this model
MyPros+ Max

Diagnose your Jenn-Air JJW9530DDW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (48)

CodeMeaning
1c1cShorted key detected on the control circuit board.1c2cKeyboard tail disconnected from control board.1c31Cancel key circuit problem (upper/single oven cavity).1c32Cancel key circuit problem (lower oven cavity).1c4cPower micro communication failure (UH control only).1c6cEEPROM error1c7cControl not calibrated1c81Cook profile corrupted in EEPROM (upper/single oven cavity, UH control only).1c82Cook profile corrupted in EEPROM (lower oven cavity, UH control only).1c8cCooking program error1d11Runaway temperature (650°F) with door unlocked, upper/single oven cavity.1d12Runaway temperature (650°F) with door unlocked, lower oven cavity.1d21Runaway temperature (950°F) with door locked, upper/single oven cavity.1d22Runaway temperature (950°F) with door locked, lower oven cavity.3d11Temperature sensor open (infinite resistance), upper/single oven cavity.3d12Temperature sensor open (infinite resistance), lower oven cavity.3d21Temperature sensor shorted (0 ohms resistance), upper/single oven cavity.3d22Temperature sensor shorted (0 ohms resistance), lower oven cavity.3d41Meat probe shorted (probe resistance less than 0 ohms, UH control only).3d51Meat probe not calibrated4d11Door switch position failure during clean or keyboard lockout, upper/single…4d12Door switch position failure during clean or keyboard lockout, lower oven cavity4d21No reverse airflow fan rotation (no or low RPM), upper/single oven cavity.4d22No reverse airflow fan rotation (no or low RPM), lower oven cavity (UH control…4d31Reverse airflow fan state error4d32Reverse airflow fan state error4d41High reverse airflow fan rotation (high RPM), upper/single oven cavity (UH…4d42High reverse airflow fan rotation (high RPM), lower oven cavity (UH control…4d51Door switch circuit failure4d52Door switch circuit failure
View all 48 error codes
9d11Door latch will not lock, upper/single oven cavity.9d12Door latch will not lock, lower oven cavity.9d21Door latch will not unlock, upper/single oven cavity.9d22Door latch will not unlock, lower oven cavity.9d31Door latch state unknown9d32Door latch state unknownF-Communication error between boards.F1Power to element relay activated during time of day display.F2Over temperature sensed by control.F3Cooling fan on with no oven function selected.F4Shorted oven sensor.F5Power element relays disabled in cook mode.F7Shorted key detected on control.F8Shorted meat probe alarm.F9Door lock safety circuit on power relay board sensed.FCCommunication error between boards.FFInvalid temperature reading on power relay board.FRSecond oven error sensed (double oven only).

Service modes (29)

  • 208/240V Mode Selection["Press SETUP pad.","Press DOWN ARROW pad to scroll to 208/240 V.","Select 208 or 240.","Select SET…
  • Clear Stored Fault CodesEnter the fast test mode, then press both the Cook Time and Stop Time keys simultaneously for 5…
  • Clock and Temperature Display Change (12/24hr, °F/°C)Hold either Timer key down on power up
  • Control Lockout["Press and hold BACK and ENTER pads for 5 seconds."]
  • Demo Mode["Press SETUP pad.","Press DOWN ARROW pad to scroll to DEMO.","Select DEMO to activate.","Press…
  • Diagnostic Code Display (H1/H2 via Quick Test)Enter Quick Test mode, then press COOK & HOLD to display last diagnostic code, or press AUTOSET to…
  • Diagnostic Code Display Mode["Press SETUP pad.","Press DOWN ARROW pad three times until SERVICE is displayed.","Press SERVICE…
  • Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H1/H2 Control)Press and hold the AUTOSET pad for 3 seconds at power-up
  • Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
  • Diagnostic Code Display Mode (Last Fault)["Enter Test Mode (SETUP > DOWN ARROW x3 to SERVICE > SERVICE > hold BACK and ENTER 5 sec >…
  • Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
  • Fast Test / Diagnostic Test ModeHold the Stop Time key down at power up, OR hold the Stop Time key down for 10 seconds within 5…
  • Faults Access (EOC III Controls)1
  • JJW Models Component TestTouch the desired function pad (Bake, Broil, Convect Bake, Convect Roast, Drying, or Clean) then…
  • One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
  • Quick Test Mode (EOC III Controls)1
  • Quick Test Mode (H1 Controls - Convection Model)1
  • Quick Test Mode (H1 Controls - Non-Convection Model)1
  • Quick Test Mode (H1/H2 Control)1
  • Quick Test Mode (H2/H2.5 Controls)1
  • Quick Test Mode (H3 Controls)1
  • Quick Test Mode (M1/M2 Controls)1
  • Quick Test Mode (NSC Non-Self Clean Controls)1
  • Service Mode (EOC III Controls)1
  • Temperature Offset ChangeProgram bake above 500°F, repress bake pad and hold for 3-4 seconds (pad must be re-pushed within 3…
  • Test Mode["Press SETUP pad.","Press DOWN ARROW pad three times until SERVICE is displayed.","Press SERVICE…
  • Test Mode (UH Controls)1
  • Test Mode (UH1/UH2 Control)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass