mypros+
Model reference

Jenn-Air JDR8895ACS

Range

12 documents63 error codes31 service modes

Available documentation

Tech Sheet

  • techsheet-16023506f-fr.pdf13 pg
    Covers this model
  • Tech Sheet - 16023506 - Rev F (FR)13 pg
    Covers this model

Service Manual

  • Freestanding Double Oven Dual Fuel Range68 pg
    Covers this model
  • Service Manual - 1602341768 pg
    Covers this model
  • Maytag Heritage Wiring Diagrams _ Fault Codes MC 1124 pg
    Covers this model
  • Failure Codes And Wiring Diagrams For Maytag Heritage Gas & Electric Ranges124 pg
    Covers this model

Bulletin

  • Installation Bulletin - IDC-0008-B LP Gas Conversion1 pg
    Covers this model
  • Technical Bulletin - TDC-0097-B Ignitor Switch Failures1 pg
    Covers this model
  • Technical Bulletin - TDC-0097-B-French Ignitor Switch Failures1 pg
    Covers this model

Other

  • 1602341768 pg
    Covers this model
  • IDC 0008 B1 pg
    Covers this model

Installation Guide

  • Instruction Sheet4 pg
    Covers this model
MyPros+ Max

Diagnose your Jenn-Air JDR8895ACS.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (63)

CodeMeaning
1c1cIncorrect key value cancellation1c2cIncorrect key value cancellation1c31No response from EEPROM1c32No response from EEPROM1c4cPower micro communication failure (CRC invalid).1c6cCalibration value out of limits1c7cCalibration value out of limits1c81Cook profile corrupted in EEPROM (CRC invalid) for upper/single oven.1c82Cook profile corrupted in EEPROM (CRC invalid) for lower oven.1c8cIncorrect cyclic redundancy check1d11Upper oven sensor resistance > 2237 ohms (open/shorted sensor, upper cavity).1d12Upper oven sensor resistance > 2237 ohms (open/shorted sensor, upper cavity…1d21Lower oven sensor resistance > 2787 ohms (open/shorted sensor, lower cavity).1d22Lower oven sensor resistance > 2787 ohms (open/shorted sensor, lower cavity…3d11Meat probe sensor resistance is infinite (open circuit, upper cavity).3d12Meat probe sensor resistance is infinite (open circuit, upper cavity, second…3d21Meat probe sensor resistance is 0 ohms (shorted, lower cavity).3d22Meat probe sensor resistance is 0 ohms (shorted, lower cavity, second…3d41Meat probe shorted (probe resistance < 0 ohms).3d51Meat probe not calibrated (calibration value out of range).4d11Door switch not closed when door is locked (upper cavity).4d12Door switch not closed when door is locked (upper cavity, second occurrence).4d21No Reverse Airflow Fan rotation (no/low RPM) in upper/single oven.4d22No Reverse Airflow Fan rotation (no/low RPM) in lower oven.4d31Reverse Airflow Fan state error4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) in upper/single oven.4d42High Reverse Airflow Fan rotation (high RPM) in lower oven.4d51Door switch is neither open nor closed (indeterminate state, upper cavity).4d52Door switch is neither open nor closed (indeterminate state, lower cavity).
View all 63 error codes
9d11Lock switch not closed (latch not in locked position, upper cavity).9d12Lock switch not closed (latch not in locked position, upper cavity, second…9d21Unlock switch not closed (latch not in unlocked position, upper cavity).9d22Unlock switch not closed (latch not in unlocked position, lower cavity).9d31Latch is simultaneously in locked and unlocked position (upper cavity).9d32Latch is simultaneously in locked and unlocked position (lower cavity).EEControl cannot read EEPROM; unit will shut down.F0-0No fault present; default from factory.F1-1Upper oven temperature exceeds 650°F with door unlocked.F1-2Lower oven temperature exceeds 650°F with door unlocked.F1-3Upper oven temperature exceeds 950°F with door locked.F1-4Lower oven temperature exceeds 950°F with door locked.F1-5Upper hardware failure within control.F1-6Lower hardware failure within control.F1-7Membrane switch is not responding.F1-8Shorted key in membrane switch.F1-9Internal communication errors within control.F1-AUpper latch switches failure.F1-BLower latch switches failure.F1-CUpper door switch failure.F1-DLower door switch failure.F1-ESensor input not calibrated.F1-HEEPROM error.F1-LTemperatures in both ovens are the same for a long period.F1-NInternal voltage on control not working.F3-1Upper oven sensor is shorted (below 100 ohms) or open (above 5K ohms).F3-2Lower oven sensor is shorted (below 100 ohms) or open (above 5K ohms).F9-1Upper lock switch is not correct.F9-2Upper unlock switch is not correct.F9-3Control does not see upper door lock.F9-4Lower lock switch is not correct.F9-5Lower unlock switch is not correct.F9-6Control does not see lower door lock.

Service modes (31)

  • 12/24 Hour Clock TogglePress UPPER CANCEL and FAVORITE simultaneously for 3 seconds.
  • Beep Volume AdjustmentPress UPPER CANCEL and DELAY simultaneously for 3 seconds.
  • Child Safety LockPress UPPER CANCEL and COOK & HOLD simultaneously for 3 seconds.
  • Diagnostic Code Display (alternative entry)Press and hold UPPER CANCEL and AUTOSET pads for 3 seconds
  • Diagnostic Code Display ModePress UPPER CANCEL and AUTOTEST keys simultaneously for 3 seconds
  • Diagnostic Code Display Mode (H1)Press and hold the Autoset pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H2.5)Press and hold Upper Cancel and Autoset pads for 3 seconds
  • Diagnostic Code Display Mode (H3)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up
  • Diagnostic Code Display Mode (M1/M2)Diagnostic Code Display Mode can only be started within 30 seconds when powering up the control.
  • Diagnostic Code Display Mode (NSC)Press and hold More + pad for 3 to 5 seconds within 60 seconds of powering up the unit. Cycle…
  • Engineering Test ModePress BAKE pad, enter 100°F using number pads, then immediately push and hold BAKE pad for…
  • Factory Default ResetPress UPPER CANCEL and UPPER KEEP WARM simultaneously for 3 seconds.
  • Faults Access (EOC III)1
  • Lower Oven Temperature Calibration1
  • One-Watt Standby Mode (NSC)Press and hold Cancel and Less
  • Quick Test Mode1
  • Quick Test Mode (EOC III)1
  • Quick Test Mode (H1 Convection Model)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H1 Non-Convection Model)1. Press and hold Cancel and Toast pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H2/H2.5 Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H3 Control)1. Press and hold Upper Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (M1/M2 Control)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (NSC Non-Self Cleaning Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds within 5 minutes of power-up. 2. Release…
  • Quick Test Setup OptionsWhile in Quick Test Mode, press the 0 pad
  • Sabbath ModePress and hold CLOCK for 3 to 5 seconds to activate Sabbath mode.
  • Service Mode (EOC III)1
  • Temperature Display (F/C toggle)Press UPPER CANCEL and UPPER BAKE simultaneously for 3 seconds.
  • Test Mode (Component Activation)Must be activated within the first 5 minutes of power up
  • Test Mode (UH Control)1
  • Time Display TogglePress UPPER CANCEL and CLOCK simultaneously for 3 seconds.
  • Upper Oven Temperature Calibration1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass