Model reference

KitchenAid KDFE104HWH1

Dishwasher

6 documents47 error codes6 service modes

Available documentation

Service Manual

jobaid w10573282120 pg
Covers this model
2013 Stainless Steel Tall Tub Dishwasher120 pg
Covers this model

Tech Sheet

Tech Sheet ADB1500ADS16 pg
Covers this model
Tech Sheet W11266094A16 pg
Covers this model

Service Flash

Technical Service Pointer - W11753104 - Stainless Steel Dishwasher Models False F10E5 Error6 pg
Covers this model

Other

Service Pointer - W11807380 - Rev A - Service Tool 2.0 Bluetooth Connection6 pg
Covers this model

MyPros+ Max

Diagnose your KitchenAid KDFE104HWH1.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·KitchenAid Dishwasher

1-1 on my KitchenAid KDFE104HWH1

M+

Control detected K1 pilot relay stuck

From Tech Sheet W16634845, p.17:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (47)

CodeMeaning

1-1Control detected K1 pilot relay stuck closed.1-2Control software issue 10-1Dispenser electrical problem 10-3Drying fan error 2-2No response from User Interface (UI)3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Shorted temperature sensing circuit 3-3Failed OWI calibration 4-3Wash motor not running 5-1Door stuck open 5-2Door stuck closed 6-1Low/no water (mechanical problem)6-2Fill valve electrical problem 6-3Suds/air in pump 6-4Float switch open 7-1No heat 7-2Heater stuck on 8-2Drain motor electrical problem 9-1Diverter can't find position 9-2Diverter stuck on 9-3Diverter disc missing F10E1Dispenser electrical problem F10E2Vent wax motor electrical problem F10E3Drying fan error F1E1Control detected K400 pilot relay stuck closed.F1E2Damaged or corrupted memory on control board; incompatible software components…F2E1Control detected stuck key(s) in keypad or keypad connection.F2E2User interface cannot communicate with main control; loose user interface…F3E1Open connection or component in temperature sensing circuit; open or faulty…F3E2Shorted connection or component in temperature sensing circuit; incoming water…

View all 47 error codes

F3E3OWI calibration failure.F4E4Wash motor failure due to loose connection in wash motor circuit and/or open…F5E1Door was not latched within 3 seconds of pressing Start/Resume, or loose…F5E2Control suspects door switch is stuck closed; control programmed to not start…F6E1Low or no water (mechanical problem)F6E2Fill valve electrical problem F6E3Suds/air in pump F6E4Float switch open F6E6Cool water F7E1No heat F7E2Heater stuck on F8E1Slow drain F8E4Drain motor electrical problem F9E1Diverter can't find position F9E2Diverter stuck on F9E3Diverter disc missing F9E4Lower spray arm error

Service modes (6)

Clear Customer Error HistoryDuring Service Diagnostic Cycle Interval 4, press HI TEMP key to clear customer error history.
Rapid Advance ModeAfter starting a cycle, press HI TEMP
Rapid Advance Mode (during normal cycle)Press HI TEMP
Service Diagnostic CycleWith dishwasher in standby mode, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more…
Service Diagnostics CycleWhile in Standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
Service Diagnostics with Error CodesPress any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second between key presses.

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass