mypros+
Model reference

Maytag MER6751AAW

Range

11 documents66 error codes47 service modes

Available documentation

Tech Sheet

  • Technical Information⎯Double Oven Electric Range14 pg
    Covers this model
  • Technical Information⎯Double Oven Electric Range6 pg
    Covers this model

Service Manual

  • Oven Range Service Manual85 pg
    Covers this model
  • Freestanding Double Oven Electric Range85 pg
    Covers this model
  • Service Manual85 pg
    Covers this model
  • Service Manual - Freestanding Double Oven Electric Range85 pg
    Covers this model
  • Maytag Freestanding Double Oven Electric Range Service Manual85 pg
    Covers this model
  • Failure Codes and Wiring Diagrams for Maytag Heritage Gas & Electric Ranges124 pg
    Covers this model
  • Failure Codes And Wiring Diagrams For Maytag Heritage Gas & Electric Ranges124 pg
    Covers this model

Service Flash

  • Technical Bulletin - TDC-0096-B Oven Door Handles Breaking_TDC-0096-B2 pg
    Covers this model

Other

  • TDC 0096 B2 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MER6751AAW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (66)

CodeMeaning
1c1cShorted key detected on the control circuit board.1c2cKeyboard tail disconnected; keyboard loop reading improper value.1c31Cancel key circuit problem (upper oven / single cavity).1c32Cancel key circuit problem (lower oven).1c4cMicro communication failure.1c5cVCC or ground fault on control circuit board.1c6cEEPROM error; no response from EEPROM after 3 tries.1c7cControl not calibrated; calibration value out of range.1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1c8cCooking program error; CRC invalid.1d11Runaway temperature (650°F) detected with door unlocked (upper/single cavity).1d12Runaway temperature (650°F) detected with door unlocked (lower cavity).1d21Runaway temperature (950°F) detected with door locked (upper/single cavity).1d22Runaway temperature (950°F) detected with door locked (lower cavity).3d11Temperature sensor open (single cavity or upper cavity); sensor resistance…3d12Temperature sensor open (lower cavity); sensor resistance reads infinite.3d21Temperature sensor shorted (upper/single cavity); sensor resistance reads 0…3d22Temperature sensor shorted (lower cavity); sensor resistance reads 0 ohms.3d41Meat probe shorted3d51Meat probe not calibrated4d11Door switch position failure4d12Door switch position failure4d21No Reverse Airflow Fan rotation (no/low RPM) on upper/single oven cavity.4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse Airflow Fan state error4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch circuit failure
View all 66 error codes
4d52Door switch circuit failure9d11Door latch will not lock (upper/single cavity); lock switch not closed when it…9d12Door latch will not lock (lower cavity); lock switch not closed.9d21Door latch will not unlock (upper/single cavity); unlock switch not closed when…9d22Door latch will not unlock (lower cavity); unlock switch not closed.9d31Latch state unknown9d32Latch state unknown9d41Latch state unknown9d42Latch state unknownEEControl cannot read EEPROM; unit will shut down.F0-0No fault (default from factory).F1-1Upper oven temperature >650°F with door unlocked.F1-2Lower oven temperature >650°F with door unlocked.F1-3Upper oven temperature >950°F with door locked.F1-4Lower oven temperature >950°F with door locked.F1-5Upper hardware failure within control.F1-6Lower hardware failure within control.F1-7Membrane switch is not responding.F1-8Shorted key in membrane switch.F1-9Internal communication errors within control.F1-AUpper latch switches failure.F1-BLower latch switches failure.F1-CUpper door switch failure.F1-DLower door switch failure.F1-ESensor input not calibrated.F1-HEEPROM error.F1-LTemperatures in ovens are the same for a long period.F1-NInternal voltage on control not working.F3-1Upper sensor is shorted (<100 ohms) or open (>5K ohms).F3-2Lower sensor is shorted (<100 ohms) or open (>5K ohms).F9-1Upper lock switch is not correct.F9-2Upper unlock switch is not correct.F9-3Control does not see upper door lock.F9-4Lower lock switch is not correct.F9-5Lower unlock switch is not correct.F9-6Control does not see lower door lock.

Service modes (47)

  • 24 Hour Clock Toggle["Press and hold UPPER CANCEL and DELAY pads for 3 seconds."]
  • Beeper Volume Adjustment["Hold UPPER CANCEL and MORE (+) pads for 3 seconds to adjust beeper loudness level."]
  • Child Lock Out["Press and hold UPPER CANCEL and COOK & HOLD pads for 3 seconds.","OFF will display where the…
  • Child Lock Out (H2 Control)Press and hold Upper Cancel and Cook & Hold pads for 3 seconds
  • Child Lock Out (H3 Control)Press and hold Upper Cancel and Cook & Hold pads for 3 seconds
  • Child LockoutPress and hold Upper Cancel and Cook & Hold pads for 3 seconds
  • Clock Display Toggle["Press and hold UPPER CANCEL and CLOCK pads for 3 seconds."]
  • Clock Display Toggle (On/Off)Press and hold Upper Cancel and Clock pads for 3 seconds.
  • Demo Mode["Press and hold UPPER CANCEL and LESS (-) pads for 3 seconds."]
  • Diagnostic Code Display["Press and hold UPPER CANCEL and TIMER pads for 3 seconds within 5 minutes of power-up.","Cycle…
  • Diagnostic Code Display ModeEnter Quick Test Mode (press and hold UPPER CANCEL and UPPER BROIL pads for 3 seconds within 5…
  • Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H2 Control - MER6875A**)["Must be within 5 minutes of power-up.","Press and hold UPPER CANCEL and UPPER BROIL pads for 3…
  • Diagnostic Code Display Mode (H2 Control)Enter Quick Test Mode (press and hold UPPER CANCEL and UPPER BROIL for 3 seconds within 5 minutes…
  • Diagnostic Code Display Mode (H3 Control - MER6555A**, MER6751AA*, MER6755A**, MER6775A**)["Must be within 5 minutes of power-up.","Press and hold UPPER CANCEL and TIMER pads for 3…
  • Diagnostic Code Display Mode (H3 Control)Enter Quick Test Mode (press and hold UPPER CANCEL and TIMER for 3 seconds within 5 minutes of…
  • Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
  • Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
  • Engineering Test Mode["Press BAKE pad.","Enter 100°F using the number pads.","Immediately push and hold BAKE pad for…
  • Factory Default (Clock Reset)Press and hold Upper Cancel and Warm pads for 3 seconds.
  • Factory Default Reset["Press and hold UPPER CANCEL and WARM pads for 3 seconds."]
  • Faults Access (EOC III Controls)1
  • Lower Oven Temperature Adjustment["Press LOWER BAKE pad.","Enter 550 on the digit-pad.","Immediately press and hold LOWER BAKE pad…
  • One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
  • Quick Test Mode["Within 5 minutes of power-up, press and hold UPPER CANCEL and UPPER BROIL pads simultaneously for…
  • Quick Test Mode - Component ActivationPress and hold UPPER CANCEL and BROIL pads for 3 seconds
  • Quick Test Mode (EOC III Controls)1
  • Quick Test Mode (H1 Controls - Convection Model)1
  • Quick Test Mode (H1 Controls - Non-Convection Model)1
  • Quick Test Mode (H2 Control - MER6875A**)Within 5 minutes of power-up, press and hold UPPER CANCEL and UPPER BROIL pads for 3 seconds
  • Quick Test Mode (H2/H2.5 Controls)1
  • Quick Test Mode (H3 Control - MER6555A**, MER6751AA*, MER6755A**, MER6775A**)Within 5 minutes of power-up, press and hold UPPER CANCEL and TIMER pads for 3 seconds.
  • Quick Test Mode (H3 Controls)1
  • Quick Test Mode (M1/M2 Controls)1
  • Quick Test Mode (NSC Non-Self Clean Controls)1
  • Quick Test Setup Options["Enter Quick Test Mode first.","Press the 0 pad.","'Press Desired Pad for Selection' will scroll…
  • Sabbath Mode["Oven must be in BAKE mode before enabling.","Hold CLOCK pad for 5 seconds to activate Sabbath…
  • Sabbath Mode (H2 Control)Hold Clock pad for 3 to 5 seconds to activate Sabbath mode.
  • Sabbath Mode (H3 Control)Hold Clock pad for 5 seconds to activate Sabbath mode
  • Service Mode (EOC III Controls)1
  • Setup Options ModeWhile in Quick Test Mode, press the 0 pad
  • Temperature Display (°F/°C toggle)Press and hold Upper Cancel and Upper Bake pads for 3 seconds.
  • Temperature Display (F/C toggle)["Press and hold UPPER CANCEL and UPPER BAKE pads for 3 seconds."]
  • Test Mode["Must be activated within first 5 minutes of power up.","Press BROIL and CANCEL pads for…
  • Test Mode (ERC)Must be activated within the first 5 minutes of power up
  • Test Mode (UH Controls)1
  • Upper Oven Temperature Adjustment["Press UPPER BAKE pad.","Enter 550 on the digit-pad.","Immediately press and hold UPPER BAKE pad…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass