mypros+
Model reference

Maytag MVW6230RHW0

Washer

13 documents25 error codes7 service modes

Available documentation

Tech Sheet

  • MVW6230HC tech sheet70 pg
    Covers this model

Wiring Diagram

  • Wire Diagram W11250100 RevD2 pg
    Covers this model

Service Flash

  • Service Pointer - W11499341 - Rev B - Maytag 4.7_5.3CF Top Load Washers Extra Power Water Level Clarification3 pg
    Covers this model
  • Service Pointer - W11617330 - Rev A - Top Load Washers Out-of-Balance Condition Notifications8 pg
    Covers this model
  • Technical Service Pointer - Grinding Noise in Spin Cycle3 pg
    Covers this model
  • Service Pointer - W11632927 - Rev I - Top Load Washer Will Not Run Cycle and/or GFCI Ground Fault Failure9 pg
    Covers this model
  • Technical Service Pointer12 pg
    Covers this model

Tech Tip

  • Instruction Sheet22 pg
    Covers this model

Training

  • Training Manual Service Tool31 pg
    Covers this model

Quick Reference

  • Quick Reference Manual20 pg
    Covers this model
  • Quick Reference Guide24 pg
    Covers this model
  • Quick Reference Guide24 pg
    Covers this model

Other

  • Service Pointer - W11564098 - Rev A - Top Load Washers Clean Washer Error F0E76 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVW6230RHW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (25)

CodeMeaning
F0E2Oversuds conditionF0E3OverloadF0E4Spin limited by water temperatureF0E5Off balance load detected.F0E7Load detected when running Clean Washer cycle.F0E8Water RingF0E9OB PauseF1E1Main Control (ACU) fault.F2E1HMI stuck buttonF2E2HMI disconnected from the ACU.F3E2Pressure system faultF3E3Inlet water temperature faultF5E1Lid switch faultF5E3Lid lock will not unlockF5E4Lid not opened between cycles.F6E1Communication errorF7E1Tachometer missing or wrong signalF7E3Basket engaged during washF7E4Basket re-engagement failureF7E6Motor circuit openF7E7Motor unable to reach target RPM.F8E1Long fillF8E3Overflow or flood conditionF8E6Water hazardF9E1Drain pump system problem

Service modes (7)

  • Component Activation Mode["Enter Service Mode.","Navigate to Service Diagnostics.","Select Component Activation.","Use…
  • Diagnostic Cycle["Enter Service Mode.","Navigate to Service Diagnostics.","Select Diagnostic Cycle.","Press…
  • DLMS Calibration Cycle["Enter Service Mode.","Navigate to Factory Diagnostics.","Select DLMS Calibration Cycle."]
  • Fault History["Enter Service Mode.","Navigate to Fault History.","Press Select/Enter to view."]
  • HMI Test["Enter Service Mode.","Navigate to Service Diagnostics.","Select HMI Test.","Select from Key Test…
  • Sensor Feedback Mode["Enter Service Mode.","Navigate to Service Diagnostics.","Select Sensor Feedback.","Use Left/Right…
  • Service Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Select any three (3)…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass