mypros+
Model reference

Maytag MVW6500MBK0

Washer

7 documents34 error codes10 service modes

Available documentation

Tech Sheet

  • W11553328C Tech Sheet2 pg
    Covers this model

Service Manual

  • Technical Manual - Maytag Pet Pro System Top Load Washer49 pg
    Covers this model

Service Flash

  • Technical Service Pointer - Grinding Noise in Spin Cycle3 pg
    Covers this model
  • Technical Service Pointer #W11750573 Rev. B - Vertical Drain Pump Not Draining8 pg
    Covers this model
  • Technical Service Pointer12 pg
    Covers this model

Quick Reference

  • Quick Start Guide2 pg
    Covers this model
  • Manual de referencia rápida1 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVW6500MBK0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (34)

CodeMeaning
F0E2Oversuds condition detected.F0E3Overload condition detected.F0E4Spin limited by water temperature.F0E5Off balance load detected.F0E7Load detected when running Clean Washer cycle.F0E8Water ring condition detected.F0E9Off balance pause condition.F1E1Main Control (ACU) fault.F1E2Motor drive module over voltage.F2E1Motor drive module over temperature.F2E2Locked rotor condition detected.F2E3Locked rotor condition detected.F3E2Pressure system fault.F3E3Long fillF5E1Lid switch faultF5E3Lid will not lock or unlock.F5E4Lid not opened between cycles.F6E1Communication errorF6E3Communication errorF7E1Tachometer missing or wrong signal.F7E2MCI drive failure.F7E3Basket engaged during wash.F7E4Basket re-engagement failure.F7E6Motor circuit open.F7E7Motor unable to reach target RPM.F7E8UI stuck button detected.F7E9UI disconnected.F7EAACU/UI mismatchF7ECMotor drive module over current/overload.F8E1Inlet water temperature fault.
View all 34 error codes
F8E3Overflow or flood condition detected.F8E6Water hazard condition detected.F9E1Long drain faultF9E9Wrong voltage detected at the appliance.

Service modes (10)

  • Automatic TestPress Key 2 and then Key 5. The following tests will be performed in order
  • Automatic Test Mode["Activate Service Diagnostic Mode first.","Press and release Key 2.","Press Key 5/Start to begin…
  • Factory Mode["Ensure washer is in standby mode (plugged in with all LEDs off) and lid is closed.","Within 8…
  • Fault Code Display["Activate Service Diagnostic Mode first.","Press and release Key 3 to display the most recent…
  • Fault HistoryPress Key 3
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all LEDs off).","Within 8 seconds, press and…
  • Service Mode - Key/LED TestPress Key 1 to enter service mode
  • Software VersionPress Key 2 for 3 seconds. System will show software versions using LED group 5 and 6; each blink…
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold Key 2 for 5 seconds.","Display will…
  • UI Test["Activate Service Diagnostic Mode first.","Press and release Key 1.","All LEDs flash once, then…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass