mypros+
Model reference

Maytag MVWB965HC0

Washer

10 documents35 error codes9 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10828193 - Rev D52 pg
    Covers this model
  • FOR SERVICE TECHNICIAN'S USE ONLY - Techsheet W1082819352 pg
    Covers this model
  • Tech Sheet - W10828193 - Rev D52 pg
    Covers this model

Service Flash

  • Water Splash from Detergent Dispenser3 pg
    Covers this model
  • Technical Service Pointer - Pressure Dome Port Flash7 pg
    Covers this model

Training

  • Technical Training Pointer - Suspension Rod Bushing Elimination6 pg
    Covers this model

Quick Reference

  • Manuel de référence rapide2 pg
    Covers this model
  • Quick Start Guide2 pg
    Covers this model
  • Quick Reference Guide2 pg
    Covers this model

Installation Guide

  • Installation Instructions16 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVWB965HC0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (35)

CodeMeaning
F0E2Oversuds condition detected; suds prevent the basket from spinning up to speed…F0E3Overload detected; load size exceeds washer capacity or basket cannot be turned.F0E4Spin limited by water temperature; water temperature is too high for final spin…F0E5Off balance load detected.F1E1Main control (ACU) fault detected.F1E2Fault of the motor control section of the main control.F2E1User interface stuck button; UI is detecting a button continuously activated.F2E3UI mismatch; machine control or user interface ID does not match expected…F2E4UI software error; incompatible parameter file in the UI.F2E5UI software error; parameter memory in the UI is corrupt.F3E1Pressure system fault; main control detects an out-of-range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected open or shorted.F4E1Heater stuck on; heater is ON when it should be OFF.F4E2Heater not turning on; control has turned heater ON but cannot detect that it…F5E1Lid switch faultF5E2Lid lock will not lock or lid lock failure; lid not closed completely, lock…F5E3Lid lock will not unlock; excessive force or wash media buildup preventing lock…F5E4Lid not opened between cycles; user pressed START without opening lid between…F6E2Communication error; UI cannot hear ACU, no communication detected between UI…F6E3Communication error; ACU cannot hear UI.F7E0Loss of power; main control detects control voltage is too low or lost.F7E1Loss of power during spin; forces washer to pause for 5 minutes to allow basket…F7E2Motor drive module over temperature; main control detects a problem in the…F7E3Motor drive module over current.F7E4Motor drive module over voltage.F7E5Shifter failure; shifter is not engaging the basket for spin or disengaging it…F7E6Motor circuit loss of phase; main control detects one or more motor lines is…F7E7Motor start failure; main control unable to reach commanded motor speed.F7E8Motor stator over temperature; motor temperature is too high.F7E9Locked rotor; motor is not moving when actively driven.
View all 35 error codes
F8E1Long fill; water level does not change for a period of time or water is present…F8E3Overflow or flood condition; main control senses water level exceeding washer…F8E6Water hazard; main control senses water in tub and lid has been open for more…F9E1Long drain; water level does not change after drain pump is on.F9E2Water ring detected, pump drive system problem; system unable to drain water…

Service modes (9)

  • Fault Code DisplayFrom Service Diagnostic Mode, press and release the 3rd button used to activate Service Diagnostic…
  • Fault Code Display / Clear["Activate Service Diagnostic Mode.","Press and release the 3rd button to advance through saved…
  • Fault Code Display and Clear1
  • Key Activation & Encoder Test1
  • Load Size Calibration Cycle1
  • Service Diagnostic Mode1. Washer must be in standby mode (plugged in, all indicators off). 2. Select any 3 buttons (except…
  • Service Diagnostics Verification Cycle1
  • Service Test Mode1
  • Software Version Display1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass