mypros+
Model reference

Maytag MVWX550XW1

Washer

22 documents55 error codes27 service modes

Available documentation

Tech Sheet

  • Tech Sheet W10338674 Rev A44 pg
    Covers this model
  • tech sheet w10338674 reva44 pg
    Covers this model
  • Kenmore Whirlpool Washer 110 28002011 Tech Sheet44 pg
    Covers this model
  • Service Technical Sheet W1024050444 pg
    Covers this model

Service Manual

  • JobAidW10372167L8586 pg
    Covers this model
  • Direct Drive FL Washer86 pg
    Covers this model
  • Vertical Modular Washer84 pg
    Covers this model

Service Flash

  • TECHNICAL SERVICE POINTER - Testing Agitation during a TEST MODE2 pg
    Covers this model
  • TECHNICAL SERVICE POINTER - Top Load Washers with Dispenser Drawer6 pg
    Covers this model
  • Technical Service Pointer2 pg
    Covers this model
  • Technical Service Pointer - Service Pointer - 8178818 (Not Spinning)6 pg
    Covers this model
  • Service Pointer - W10411107 (Broken Lid Lock)1 pg
    Covers this model
  • Technical Service Pointer - VMW HE / Hybrid Washers New Plastic Drive Hub6 pg
    Covers this model
  • Service Pointer - W10405379 - Rev A (Elimination of Counter Weight)1 pg
    Covers this model
  • Technical Service Pointer - Continuous Test Mode3 pg
    Covers this model
  • Technical Service Pointer #W10492393 - Drive (Splutch) Pulley Comes Loose6 pg
    Covers this model
  • Service Pointer - W10611623 - Drain Hose Installation6 pg
    Covers this model

Tech Tip

  • Instruction Sheet2 pg
    Covers this model
  • Service Pointer - W10657326 (Customer Tip Sheet)3 pg
    Covers this model

Training

  • Training Pointer - 8178817 (Washer not Filling at Cycle)3 pg
    Covers this model
  • Technical Training Pointer - VMW HE / Hybrid Washers New Plastic Drive Hub6 pg
    Covers this model

Installation Guide

  • Instrucciones de instalación10 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVWX550XW1.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (55)

CodeMeaning
F0 E0No fault codes stored in memory.F0 E2Over suds condition detectedF0 E4High water temperature detected during rinse cycle (105°F or higher).F0 E5Off balance load detected.F0E0No fault codes stored in memory.F0E1Load detected during the washer cleaning cycleF0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected.F1 E1Main control fault.F1 E2Motor control faultF1E1CCU errorF1E2MCU errorF2 E1Stuck keyF2 E3Mismatch of Main Control and UIF2E1Stuck key detected; one or more keys on the User Interface were actuated for 15…F2E3Unsupported cycleF3 E1Pressure sensor faultF3 E2Inlet water temperature faultF3E1Pressure switch/pressure sensor errorF3E2Temperature sensor errorF5 E1Lid switch faultF5 E2Lid lock faultF5 E3Lid unlock faultF5 E4Lid not opened between cyclesF5E1Door switch errorF5E2Door lock errorF5E3Door unlock errorF5E4Lid not opened between cycles; user presses START after several consecutive…F6E1Communication error between CCU and MCU
View all 55 error codes
F6E2Communication error UI to CCUF6E3Communication error CCU to UIF7 E1Basket speed sensor faultF7 E5Shifter faultF7 E6Motor faultF7 E7Motor unable to reach target RPMF7E1Drive motor tachometer error / washer overloadF7E2MCU fault or motor overheatF7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; open clockwise or counterclockwise circuit of the motor.F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8 E1No fill / long fillF8 E3Overflow conditionF8 E5Hot and cold water supply hoses are reversed.F8E0Steam inlet valve errorF8E1No water detected entering washer or pressure switch trip not detectedF8E2Dispenser system errorF8E3Overflow conditionF8E4Flow meter faultF8E5Hot and cold inlet hoses are reversed.F9 E1Long drainF9E1Long drainIntInterruptedrLRemove loadSudSuds detected

Service modes (27)

  • Automatic Test Mode["Activate diagnostic test mode.","Turn cycle selector knob until Spin LED is On and display shows…
  • automatic_test["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Spin LED…
  • calibration["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Rinse LED…
  • Calibration Mode["Activate diagnostic test mode.","Turn cycle selector knob until Rinse LED is On and display shows…
  • Clear Fault Codes1
  • diagnostic["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Fault Code DisplayFrom Service Diagnostic Mode, press and release the 3rd button used to activate Service Diagnostic…
  • Fault Code Display / Advance1
  • Fault Code Display Mode["Activate diagnostic test mode (see entry sequence above).","Turn cycle selector knob until Done…
  • fault_code_display["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Done LED…
  • Manual Test Mode["Activate diagnostic test mode.","Turn cycle selector knob until Spin & Done LEDs are On and…
  • manual_test["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Spin &…
  • Quick Diagnostics1
  • Sales Demo Mode["Activate diagnostic test mode.","Turn cycle selector knob until Rinse & Done LEDs are On and…
  • Service Diagnostic Mode1. Ensure washer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Service Diagnostic Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Software Version Display1
  • Software Version Display Mode["Activate diagnostic test mode.","Turn cycle selector knob until Rinse, Spin, and Done LEDs are On…
  • sw_version_display["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Rinse…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Wash and Done LEDs are On…
  • tachometer_verification["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Wash and…
  • UI Test Mode["Activate diagnostic test mode.","Turn cycle selector knob until Rinse & Spin LEDs are On and…
  • ui_test["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Rinse &…
  • User Interface Test1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass