Model reference
Whirlpool 7WDT950SAYM2
Dishwasher
9 documents32 error codes7 service modes
Available documentation
Tech Sheet
- Tech Sheet - W10679637 - Rev A (SP)16 pg
Service Manual
- Kenmore Elite 2013 Stainless Steel Tall Tub Dishwashers82 pg
Tech Tip
- Instruction Sheet4 pg
- Instruction Sheet2 pg
- quickreferenceinsertsheet-w10164331-reva-sp.pdf1 pg
Installation Guide
- Instrucciones de instalacion23 pg
- Instruction Sheet2 pg
- Instruction Sheet for Heater Element kit2 pg
Other
- technicalreferencemanual 2211031382 pg
MyPros+ Max
Diagnose your Whirlpool 7WDT950SAYM2.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (32)
CodeMeaning
1-1Control detected K400 pilot relay stuck closed.1-2Damaged or corrupted memory on control board; incompatible software components…10-1Dispenser electrical problem; loose connection in dispenser circuit and/or open…10-2Vent wax motor electrical problem; loose connection in vent circuit and/or open…10-3Drying fan error; loose connection in fan circuit and/or open fan motor; faulty…2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control; loose user interface…3-1Open connection or component in temperature sensing circuit; open or faulty…3-2Shorted connection or component in temperature sensing circuit; shorted or…3-3OWI failure; failed calibration.4-1Wash motor does not run4-2Wash motor4-4Wash motor failure; loose connection in wash motor circuit and/or open wash…5-1Door stuck open; door was not latched within 3 seconds of pressing…5-2Door stuck closed; control programmed to not start if it suspects door switch…6-1Low/no water (mechanical problem); no water to dishwasher, bowls capturing wash…6-2Fill valve electrical problem; loose connection in fill valve circuit and/or…6-3Suds/air in pump; too many suds, bowls capturing wash water, water leaking…6-4Float switch open; overfill switch stuck in open position and/or dishwasher not…6-6Cool water; incoming water temperature under 18°C/65°F.6-7Water inlet6-8Water inlet7-1No heat; control programmed to disable heater if it detects a water heating…7-2Heater stuck on; faulty heater drive circuit on the control.8-1Slow drain; obstructed drain hose or path; drain pump impeller fractured or…8-2Drain8-3Drain8-4Drain motor electrical problem; loose connection in drain motor circuit and/or…9-1Diverter can't find position; corroded or loose connection in diverter…9-2Diverter stuck on; faulty diverter drive circuit on the control.Service modes (7)
- Control LockPress and hold the Control Lock button for 5 seconds to toggle on/off.
- Error Code ReadingEnter Service Diagnostics mode (1-2-3-1-2-3-1-2-3)
- Rapid Advance Mode (Customer Cycles)Press HIGH TEMP
- Rapid Advance Mode (during active cycle)After starting a cycle, press HI TEMP
- Sales Demo Mode ClearRun Service Diagnostics Cycle to clear demo mode.
- Service Diagnostic CycleWith dishwasher in standby, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more than…
- Service Diagnostics Cycle1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool dishwasher models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax