Model reference

Whirlpool WDL785SAAM0

Dishwasher

12 documents43 error codes5 service modes

Available documentation

Service Manual

6th Sense Live - Connected Smart Appliances84 pg
Covers this model

Tech Sheet

Tech Sheet - W10505257 - Rev A16 pg
Covers this model

Service Flash

Technical Service Pointer - W10475713 - Rev A (Vent Removed)3 pg
Covers this model
Technical Service Pointer - Upper Rack Wheel & Mount Assembly9 pg
Covers this model

Tech Tip

Instruction Sheet2 pg
Covers this model
Installation Instructions6 pg
Covers this model

Installation Guide

Instruction Sheet1 pg
Covers this model
Installation Instructions48 pg
Covers this model
Instruction Sheet for Heater Element kit2 pg
Covers this model

Quick Reference

Quick Reference Manual2 pg
Covers this model
Quick Reference Manual1 pg
Covers this model

Other

Whirlpool Dishwasher WDT910SAYE0 WDT910SAYH0 WDT910SAYM0 Users Manual W1035035940 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WDL785SAAM0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Dishwasher

1-1 on my Whirlpool WDL785SAAM0

M+

Control detected K2 pilot relay stuck

From Tech Sheet W17621465, p.37:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (43)

CodeMeaning

1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem 10-2Vent wax motor electrical problem 10-3Drying fan error 12-1No communication between ECM and control 12-2No link between ECM and wireless router 12-3No link between ECM and Internet 12-4Antenna A problem 12-5Antenna B problem 12-6Current Transformer problem 12-7Provisioning problem 2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface problem (capacitive touch keypad adhesive, moisture, or debris…3-1Open connector or component in Temperature Sensing circuit, open or faulty…3-2Shorted connection or component in Temperature Sensing circuit, incoming water…3-3OWI (optical soil sensor) failure or failed calibration due to drain hose check…4-3Wash motor not running due to loose connection in Motor circuit and/or faulty…5-1Door was not latched within 3 seconds of pressing Start/Resume, or loose…5-2Door switch stuck closed 6-1Low/no water (mechanical problem)6-2Fill valve electrical problem 6-3Suds/air in pump 6-4Float switch open 6-6Cool water 6-7Flow Meter disconnected or damaged.6-8Water Softener Regen Valve electrical problem 7-1No heat 7-2Heater stuck on 8-1Slow drain

View all 43 error codes

8-2Drain motor electrical problem 8-3Drain stuck on 9-1Diverter can't find position 9-2Diverter stuck on 9-3Diverter disk missing FCE0No communication between ECM and Control FCE1No link between ECM and Wireless Router FCE2No link between ECM and Internet FCE3Antenna A problem FCE4Antenna B problem FCE5Current Transformer A problem FCE6Current Transformer B problem FCE7Provisioning problem

Service modes (5)

Component Activation - Dryer["Activate Service Diagnostic Mode","From the Diagnostic Home Screen, select Component…
Component Activation - Washer["Activate Service Diagnostic Mode","From the Diagnostic Home Screen, select Component…
Error Code History DisplayEnter Service Diagnostics Cycle (1-2-3-1-2-3-1-2-3)
Rapid Advance ModePress HI TEMP
Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass