Model reference

Whirlpool WDT920SADE0

Dishwasher

9 documents33 error codes8 service modes

Available documentation

Tech Sheet

Tech Sheet W1061005912 pg
Covers this model
KDTE104ESS3 Tech Sheet12 pg
Covers this model
Whirlpool Dishwasher WDF760SADM0 Tech Sheet W1061005912 pg
Covers this model
Fiche technique W10610060B16 pg
Covers this model

Service Manual

Kenmore Elite 2013 Stainless Steel Tall Tub Dishwashers82 pg
Covers this model

Service Flash

Technical Service Pointer #W10777966 - Detergent Dispenser Door Hitting Silverware Blast Zone3 pg
Covers this model
Technical Service Pointer - W10841713 (Door Clicking)6 pg
Covers this model

Installation Guide

Installation Instructions48 pg
Covers this model

Other

technicalreferencemanual 2211031382 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WDT920SADE0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Dishwasher

1-1 on my Whirlpool WDT920SADE0

M+

Control detected K2 pilot relay stuck

From Tech Sheet W13656887, p.19:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (33)

CodeMeaning

1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory or control board, incompatible software components…10-1Dispenser electrical problem 10-2Vent wax motor electrical problem; loose connection in vent circuit and/or open…10-3Drying fan error 2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control 3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Incoming water temperature above 167°F (75°C), or shorted connection or…3-3OWI (optical soil sensor) calibration failure.4-3Wash motor not running due to loose connection in Motor circuit and/or faulty…4-4Wash motor failure; loose connection in wash motor circuit and/or open wash…5-1Door stuck open 5-2Door stuck closed 6-1Inlet water low/no water (mechanical problem)6-2Inlet water fill valve electrical problem 6-3Suds/air in pump 6-4Float switch open 6-6Incoming water cool 6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem 7-1No heat 7-1 (flowmeter)Disconnected or damaged flowmeter.7-2Heater stuck on 8-1Slow drain 8-2Drain motor electrical problem 8-3Drain stuck on 8-4Drain motor electrical problem; loose connection in drain motor circuit and/or…8-5Drain stuck on 9-1Diverter can't find position

View all 33 error codes

9-2Diverter stuck on 9-3Diverter disk missing 9-4Lower spray arm error; mechanical binding or blocking of spray arm; corroded or…

Service modes (8)

Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
Rapid Advance (Customer Cycles)After starting a customer cycle, press HIGH TEMP
Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
Rapid Advance Mode (during active cycle)After starting a cycle, press HI TEMP
Sales Demo Mode ClearRun Service Diagnostics Cycle to clear demo mode.
Service Diagnostic CycleWith dishwasher in standby, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more than…
Service Diagnostics Cycle1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass