Model reference

Whirlpool GY395LXGZ0

Range

7 documents29 error codes6 service modes

Available documentation

Tech Sheet

Wiring Sheet - 97528751 pg
Covers this model
Whirlpool Range GY396LXGQ2 Tech Sheet8 pg
Covers this model
Whirlpool Range GY396LXGQ4 Tech Sheet8 pg
Covers this model

Service Manual

Whirlpool Self-cleaning Slide-in Electric Ranges66 pg
Covers this model
Self-Cleaning Slide-In Electric Ranges - Job Aid66 pg
Covers this model

Installation Guide

Instruction Sheet2 pg
Covers this model
Installation Instructions5 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool GY395LXGZ0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

F1 on my Whirlpool GY395LXGZ0

M+

EEPROM communications error or EEPROM

From Tech Sheet W15205185, p.37:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (29)

CodeMeaning

F1EEPROM communications error or EEPROM checksum failure.F1 E0EEPROM communications failure.F1 E1EEPROM checksum failure.F1 E2UL A/D error(s).F1-E0EEPROM communications failure.F1-E1EEPROM checksum failure.F1-E2UL A/D error(s).F2Shorted key, keytail unplugged, or UL A/D error(s).F2 E0UL A/D error(s).F2 E1Keytail unplugged.F2-E0Shorted key on keypad.F2-E1Keytail unplugged from control.F3Oven sensor opened or oven sensor shorted.F3 E0Oven sensor opened.F3 E0 (door/latch)Door and latch switches do not agree.F3 E1Oven sensor shorted.F3 E1 (door/latch)Solenoid not operating or latch switch failure.F3 E2Bake range over temperature condition.F3 E2 (door/latch)Latch during CLEAN error.F3 E3Clean range over temperature condition.F3-E0Oven temperature sensor circuit is open.F3-E1Oven temperature sensor is shorted.F3-E2Bake range over temperature condition.F3-E3Clean range over temperature condition.F4Bake range over temp or Clean range over temp.F5Shorted key detected on keypad.F5-E0Door switch and latch switch do not agree (mismatch).F5-E1Door lock solenoid not operating or latch switch failure.F5-E2Latch error occurring during CLEAN cycle.

Service modes (6)

Clear F-failure Code from Memory["Press and hold any key for 1 minute to clear the F-failure code from memory.","F2 will…
Last Error Code Recall["Press and hold the CANCEL/OFF key for 5 seconds.","The last error code will be displayed."]
Oven Temperature Calibration["Press and hold the BAKE keypad for 5 seconds.","The current offset (if any) will be shown in the…
Temperature Adjustment (BAKE calibration)Press and hold BAKE pad for 5 seconds. Current offset (if any) is shown on 3-digit display; CAL is…
Temperature Calibration AdjustmentPress and hold BAKE pad for 5 seconds
View Last Error Code["Press and hold the CANCEL/OFF key for 5 seconds.","The last error code will be displayed."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass