mypros+
Model reference

Whirlpool KFDC500JYP00

Range

8 documents25 error codes8 service modes

Available documentation

Tech Sheet

  • Tech Sheet96 pg
    Covers this model

Service Manual

  • Dimension Guide30 pg
    Covers this model
  • Technical Manual - W11372006 - Rev B - JennAir and KitchenAid Dual-Fuel and Gas Commercial Ranges86 pg
    Covers this model
  • Technical Manual - Cooking Surface Temperature Limits12 pg
    Covers this model

Wiring Diagram

  • Wiring Sheet W11327460 REVA2 pg
    Covers this model

Service Flash

  • Service Pointer - W11498555 - Rev B - FSR Oven Cooling Fan Noise Improvement9 pg
    Covers this model
  • Commercial Range Door Will Not Close5 pg
    Covers this model
  • Service Pointer - W11643965 - Rev A - Slow_No Ignition Commercial Range_Cooktop_W1164396512 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool KFDC500JYP00.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (25)

CodeMeaning
F1E0User Interface Board EEPROM Communication ErrorF1E1Control Relay Board EEPROM Communication ErrorF2E1Stuck KeyF2E2Oven Knob Rotary Encoder Open/ShortedF3E0Main Oven Sensor Open or ShortedF3E1Left Oven Sensor Open or ShortedF3E3Main Oven Meat Probe Short-CircuitF3E9Left Oven Meat Probe Short-CircuitF5E0Main Oven Door Latch SwitchF5E1Main Oven Door Latch MotorF5E3Left Oven Door Latch SwitchF5E4Left Oven Door Latch MotorF6E0User Interface ConnectionF6E1Main Oven Over Temperature LimitF6E3Left Oven Over Temperature LimitF6E4Control StatusF6E6Main Oven Control ConnectionF6E9Left Oven Control ConnectionF7E1Boiler Over Temperature Limit (steam models)F7E2Boiler Temperature Out of Range (for steam models)F8E0Main Oven Cooling Fan speed low or not functioningF8E1Left Oven Cooling Fan Speed LowF8E2Main Oven Cooling Fan Speed HighF8E3Left Oven Cooling Fan Speed HighF9E0Power Input

Service modes (8)

  • diagnostic["Appliance must be in standby mode.","Set Mode Selector knob to Bake position and Temperature knob…
  • Diagnostics Mode Entry1
  • Fault Code DisplayFrom Diagnostics Mode, rotate Mode Selector knob clockwise until top LEDs are on, then press Start…
  • fault_code_display["Enter Diagnostics Mode first.","Rotate Mode Selector knob clockwise until top LEDs are…
  • Manual Diagnostic["Enter Diagnostics Mode.","Rotate the Mode Selector knob clockwise until the top and right LEDs…
  • Manual DiagnosticsFrom Diagnostics Mode, rotate Mode Selector knob clockwise until top and right LEDs are on, then…
  • manual_diagnostic["Enter Diagnostics Mode first.","Rotate Mode Selector knob clockwise until top and right LEDs are…
  • Suspend Code Status (KitchenAid only)["Turn Mode Knob away from OFF and back to OFF to suspend Error Status (Amber LED) display."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass