mypros+
Model reference

Whirlpool WOD51EC0AB05

Range

6 documents20 error codes17 service modes

Available documentation

Tech Sheet

  • Whirlpool Oven WOD51EC0AB00 Tech Sheet16 pg
    Covers this model
  • WOD51EC7AS05 Tech Sheet W10886885 Rev A56 pg
    Covers this model
  • WiringDiagram-W10878728-RevA.pdf2 pg
    Covers this model
  • WiringDiagram-W10878727-RevA.pdf2 pg
    Covers this model

Installation Guide

  • Installation Instructions32 pg
    Covers this model

Other

  • W106894086 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WOD51EC0AB05.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (20)

CodeMeaning
F1E0EEPROM Communication ErrorF1E1Upper RTD UncalibratedF1E2Lower RTD UncalibratedF1E5Sensor Usage Out of RangeF1E7PCB Thermistor Open or ShortedF1E9WIDE Queue FullF2E0Keypad DisconnectedF2E1Stuck KeypadF2E2Cancel or Off Keypad ErrorF2E3Cancel key error on keypad.F3E0Main Sensor Open or Shorted (Upper)F3E1Main Sensor Open or Shorted (Lower)F4E1Microwave Oven Magnetron Thermistor Open or ShortedF4E4Microwave Oven Humidity Sensor Open or ShortedF5E0Door and Latch Switches Do Not AgreeF5E1Latch Not OperatingF6E0Lost Communication with MicrowaveF6E1Over Temp CookF6E2Over Temp CleanF9E0Miswired

Service modes (17)

  • Auto Test ModeEnter Diagnostics Mode (CANCEL > CANCEL > START)
  • Control ResetEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Control…
  • Diagnostics modePress CANCEL>CANCEL>START or OFF>OFF>ON within 5 seconds.
  • Display testEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Display'…
  • Engineering ModeEnter Diagnostics Mode (CANCEL > CANCEL > START)
  • Fault Display ResetEnter Diagnostics Mode (CANCEL > CANCEL > START)
  • Faults screenEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Faults'…
  • Oven Temperature Calibration (Double Oven)Press SETTINGS until 'TEMP CALIB' is displayed
  • Oven Temperature Calibration (Single Oven)Press SETTINGS until 'TEMP CALIB' is displayed
  • Relay ActivationEnter Diagnostics Mode (CANCEL > CANCEL > START). The control will automatically enter Test Mode…
  • Semi-Automatic Test modeEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Semi Auto…
  • Software VersionEnter Diagnostics Mode (CANCEL > CANCEL > START)
  • Temperature CalibrationPress Settings or Options keypad until 'Temp Calib' is displayed
  • Test modeEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Test…
  • UsageEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Usage' is…
  • Usage CodesEnter Diagnostics Mode (CANCEL > CANCEL > START)
  • VersionEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Version'…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass