Model reference
Whirlpool WOD93EC0AB05
Range
6 documents33 error codes16 service modes
Available documentation
Tech Sheet
- WOD51EC7AS05 Tech Sheet W10886885 Rev A56 pg
- WiringDiagram-W10878728-RevA.pdf2 pg
- WiringDiagram-W10878727-RevA.pdf2 pg
- Tech Sheet32 pg
Installation Guide
- Installation Instructions32 pg
Other
- W106894086 pg
MyPros+ Max
Diagnose your Whirlpool WOD93EC0AB05.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (33)
CodeMeaning
F1 E0Internal error on MRC board.F1 E1Internal error on MRC board.F1 E7Internal error on MRC board.F1 E9Internal error on MRC board.F1E0EEPROM Communication ErrorF1E1Upper RTD UncalibratedF1E2Lower RTD UncalibratedF1E5Sensor Usage Out of RangeF1E7PCB Thermistor Open or ShortedF1E9WIDE Queue FullF2 E0Keypad disconnected from MRC board.F2 E1Stuck key detected on keypad.F2 E2Invalid keypad detected.F2 E3Cancel key error on keypad.F2E0Keypad DisconnectedF2E1Stuck KeypadF2E2Cancel or Off Keypad ErrorF3 E0Main oven sensor open or shorted (upper cavity on single or double oven).F3 E1Main oven sensor open or shorted (lower cavity on double oven).F3E0Main Sensor Open or Shorted (Upper)F3E1Main Sensor Open or Shorted (Lower)F4E1Microwave Oven Magnetron Thermistor Open or ShortedF4E4Microwave Oven Humidity Sensor Open or ShortedF5 E0Door and latch switches do not agree.F5 E1Latch not operating.F5E0Door and Latch Switches Do Not AgreeF5E1Latch Not OperatingF6 E1Over temperature during cooking.F6 E2Over temperature during cleaning.F6E0Lost Communication with MicrowaveView all 33 error codes
Service modes (16)
- Auto Test Mode1
- Control ResetEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Control…
- Diagnostics modePress CANCEL>CANCEL>START or OFF>OFF>ON within 5 seconds.
- Display testEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Display'…
- Fault Display Reset1
- Faults screenEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Faults'…
- Semi-Automatic Test modeEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Semi Auto…
- Software Version1
- Temperature CalibrationPress Settings or Options keypad until 'Temp Calib' is displayed
- Temperature Calibration (Double Oven)1
- Temperature Calibration (Single Oven)1
- Test modeEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Test…
- Test Mode (Relay Activation)1
- UsageEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Usage' is…
- Usage Codes1
- VersionEnter Diagnostics mode, then press Temp/Time +/- or More/Less or number 3/6 keypad until 'Version'…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool range models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass