mypros+
Model reference

Whirlpool VWW3809RW0

Washer

3 documents30 error codes13 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11745851 - Rev A48 pg
    Covers this model

Service Manual

  • TECHNICAL MANUAL Maytag® Top Load Washer153 pg
    Covers this model

Quick Reference

  • Quick Start Guide2 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool VWW3809RW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (30)

CodeMeaning
F0E2Over suds condition detected; suds prevent the basket from spinning up to speed…F0E3OverloadF0E4High water temperature (105°F or higher) detected during rinse cycle.F0E5Off balance load detected.F0E7Load detected when running Clean Washer cycle.F0E8Water ringF0E9Off balance pauseF1E1Main control fault.F1E2Motor control faultF2E1Stuck keyF2E2HMI disconnected from the ACU.F2E3Switch mismatchF3E1Pressure system faultF3E2Inlet water temperature faultF5E1Lid switch faultF5E2Lid lock faultF5E3Lid unlock faultF5E4Lid not opened between cyclesF6E1Communication errorF7E1Basket speed faultF7E3Basket engaged during washF7E4Basket re-engagement failureF7E5Shifter faultF7E6Motor faultF7E7Motor unable to reach target RPMF8E1No fill / long fillF8E3Overflow conditionF8E5Hot and cold inlet hoses are reversed.F8E6Water hazardF9E1Long drain

Service modes (13)

  • Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Spin' LED is…
  • Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Rinse' LED is…
  • Factory Calibration Cycle["Ensure washer is in standby mode (plugged in with all LEDs off) and lid is closed.","Within 8…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Done' LED is…
  • Fault History Display["Enter Service Diagnostic Mode first.","Rotate encoder 3 until LED1 is ON.","Press SW2/Start…
  • Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' and 'Done' LEDs are…
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all LEDs off).","Using encoder E3 (cycle…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Wait 10 seconds after…
  • Software Version Display["Enter Service Diagnostic Mode first.","Rotate encoder 3 until LED4 turns ON.","Press SW2/Start…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse', 'Spin', and 'Done'…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash' and 'Done' LEDs are…
  • UI Test["Enter Service Diagnostic Mode first.","Rotate E3 clockwise until LED3 is ON.","Press SW2/Start…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' and 'Spin' LEDs are…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass