mypros+
Model reference

Whirlpool WTW6157PW0

Washer

9 documents34 error codes10 service modes

Available documentation

Service Manual

  • Dimension Guide12 pg
    Covers this model
  • TECHNICAL MANUAL - Whirlpool® Top Load Washer136 pg
    Covers this model
  • Energy Star Certification1 pg
    Covers this model

Tech Sheet

  • Whirlpool WTW6157PB0 Washer Tech Sheet2 pg
    Covers this model
  • Service Technician Technical Sheet W11455149B2 pg
    Covers this model
  • Service Diagnostic Tech Sheet W114551492 pg
    Covers this model

Service Flash

  • Service Pointer - W11618678 - Rev A - Top Load Washers Cycle Won't Start3 pg
    Covers this model

Quick Reference

  • Quick Start Guide2 pg
    Covers this model
  • Manual de referencia rápida1 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW6157PW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (34)

CodeMeaning
F0E2Overload condition detected.F0E3Oversuds detected in the washer.F0E4Spin limited by water temperature.F0E5Off balance load detected.F0E7Load detected when running Clean Washer cycle.F0E8Water ring condition.F0E9Off balance pause condition.F1E1Main Control (ACU) fault.F1E2Motor Drive Module over voltage.F2E1UI stuck button detected.F2E2UI disconnected from the control.F2E3ACU/UI mismatch.F3E2Pressure system fault.F3E3Inlet water temperature fault.F5E1Long fill condition detected.F5E3Lid switch faultF5E4Lid will not lock or unlock.F6E1Lid not opened between cycles.F6E3Communication errorF7E1Communication errorF7E2Tachometer missing or wrong signal.F7E3MCI drive failure.F7E4Basket engaged during wash.F7E6Basket re-engagement failure.F7E7Motor circuit open.F7E8Motor unable to reach target RPM.F7E9Motor drive module over temperature.F7EALocked rotor condition detected.F7ECMotor phase loss detected.F8E1Motor drive module over current/overload.
View all 34 error codes
F8E3Overflow or flood condition detected.F8E6Water hazard condition detected.F9E1Long drain fault.F9E9Wrong voltage detected at the appliance.

Service modes (10)

  • Automatic TestFrom service mode
  • Automatic Test Mode["Activate Service Diagnostic Mode first.","Press and release Key 2.","Press Key 5/Start to begin…
  • Factory Calibration Cycle["Ensure washer is in standby mode (plugged in with all LEDs off) and lid is closed.","Within 8…
  • Fault Code Display Mode["Activate Service Diagnostic Mode first.","Press and release Key 3 to display most recent fault…
  • Fault HistoryFrom service mode
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all LEDs off).","Within 8 seconds, perform the…
  • Service Mode Entry1. Ensure washer is in standby mode (plugged in with all LEDs off). 2. Within 8 seconds
  • Software VersionFrom service mode
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold Key 2 for 5 seconds.","Display…
  • UI TestFrom service mode

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass