Model reference

Whirlpool WTW6200SW3

Name: Whirlpool WTW6200SW3
Brand: Whirlpool

Washer

15 documents35 error codes3 service modes

Available documentation

Service Manual

Cabrio™ Automatic Washer Job Aid84 pg
Covers this model

Tech Sheet

Tech Sheet - W10026634 - Rev B16 pg
Covers this model

Service Flash

Service Pointer 8178742 - Cabrio and Bravos Washers Intermittent Water Leak4 pg
Covers this model
F1 Error Code Service Pointer Cabrio Washer2 pg
Covers this model
Service Pointer - Control Displays F51 Code1 pg
Covers this model
F1 Error Code Service Pointer - HE Top Load Washers2 pg
Covers this model
Service Pointer - 8178767 (F1 Error Code)2 pg
Covers this model
Service Pointer 8178742 Intermittent Water Leak4 pg
Covers this model
Service Pointer - W10611623 - Drain Hose Installation6 pg
Covers this model

Training

Training Pointer - Replacement Bearing Procedure for Top Load, Direct Drive Washers16 pg
Covers this model

Job Aid

Instruction Sheet for Bearing Replacement Procedure12 pg
Covers this model

Quick Reference

Quick Reference Manual4 pg
Covers this model
Manual de referencia rapida2 pg
Covers this model

Installation Guide

Instruction Sheet2 pg
Covers this model

Other

81787671 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WTW6200SW3.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Washer

dL on my Whirlpool WTW6200SW3

M+

Lid Lock Failure — lid is not closed

From Tech Sheet W11547173, p.25:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure door lock assembly resistance across PTC terminals. Expected: ~200 ohms cold.

3.Inspect strike and latch alignment. A misaligned strike prevents the switch stack from closing.

Part W10810403

Door lock assembly

Error codes (35)

CodeMeaning

dLLid Lock Failure dULid Unlock Failure F1Pressure Signal Out-of-Range F2Keypad/User Interface Failure F30Saved code for Long Fill (LF) condition.F32Saved code for Long Drain (Ld) condition.F40ATC Thermistor Open/Short F41Motor RPS Thermistor Open/Short F42Heater in unknown state F43Heater is continuously ON F44Heater cannot be turned ON F50Motor Stalled F51Motor RPS Failure F52Motor Stop Failure F53Motor Control Overtemp F54Motor Control Overcurrent F60Saved code for Primary Control Failure.F68Saved code for Primary Control Failure (range F60-F68).F70Saved code for Overloaded (oL) condition.F71Saved code for Suds Detection (Sd) condition.F72Basket Re-engagement Failure F80Saved code for Door Lock Failure (dL).F81Saved code for Open/Close Door Lid (lid) condition.F82Saved code for Door Lock Failure (dL).F83Saved code for Door Unlock Failure (dU).F84Saved code for Door Lock Failure (dL).F85Saved code for Door Lock Failure (dL).HCHot, Cold Reversed LdLong Drain LFLong Fill

View all 35 error codes

lidOpen/Close Lid oLOverloaded PoPump Out SdSuds Detection uLUnbalanced Load

Service modes (3)

Automatic Diagnostic Test Mode1. Washer must be in standby mode (plugged in with all indicators off, or with only Clothes Clean…
Console and Indicators Diagnostic Test Mode1. Plug in washer or reconnect power. 2. From Standby (Off) Mode, press and release within 4 seconds
Manual Diagnostic Test Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass