mypros+
Error code reference

Bosch Range Error Code F32

Oven sensor shorted

Bosch codesBosch range codes

Oven sensor shorted — sensor shorted to self or ground, or leads shorted.

First step from the service manual

Verify connector at P8 on relay board is secure, then check resistance at connector to chassis for open circuit, then confirm resistance at connector is approx. 1100 ohms at room temp.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F32.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F32 means on a Bosch range

The F32 error code on a Bosch range indicates that the oven temperature sensor has developed a short circuit condition. Unlike an open circuit failure where the sensor circuit is broken, a short means the sensor's resistance has dropped abnormally low, either because the sensor element has shorted internally to itself, the sensor leads have shorted together, or the sensor or its wiring has made contact with the chassis ground. The oven temperature sensor is a negative temperature coefficient (NTC) resistive element that the control board reads to determine oven cavity temperature. When the sensor shorts, the control reads an impossibly low resistance value, interprets it as an extreme temperature, and halts oven operation to prevent damage.

The first diagnostic step involves the connector at P8 on the relay board. This connector is the interface point between the oven sensor wiring harness and the control relay board. A loose or corroded connection at P8 can create intermittent or false short readings. After confirming the connector is fully seated and free of corrosion, technicians should check resistance from the sensor leads at that connector to chassis ground. Any measurable low resistance to ground confirms a short to ground in the sensor or its leads. With no short to ground present, resistance measured across the two sensor leads at the connector should read approximately 1100 ohms at room temperature.

If the connector is secure and the resistance to ground is an open circuit but the sensor-to-sensor resistance reads significantly below 1100 ohms, the sensor element itself has failed internally. If resistance to ground is low, the sensor body or leads have made contact with the oven chassis, often due to physical damage from heat cycling or improper routing. Both conditions require sensor replacement. Harness damage between P8 and the sensor is also a possibility and should be inspected visually for pinching, burning, or insulation breakdown.

Source: manufacturer service documentation.

Common causes of F32

  1. 01

    Failed oven temperature sensor (internal short)

    Part replacement

    The resistive element inside the sensor has shorted to itself, causing resistance to read far below the expected 1100 ohms at room temperature. This is the most common cause and requires sensor replacement.

  2. 02

    Sensor or leads shorted to chassis ground

    Part replacement

    The sensor body or its wiring has made contact with the oven metal chassis, likely from heat damage, insulation breakdown, or improper routing after a previous repair. Resistance measured from the sensor leads at P8 to chassis ground will be measurably low rather than an open circuit.

  3. 03

    Loose or corroded connector at P8 on relay board

    Wiring / connection

    A poorly seated or corroded connector at P8 can cause false short readings. This should be the first thing checked, as reseating or cleaning the connector may resolve the code without parts replacement.

  4. 04

    Pinched or damaged sensor wiring harness

    Part replacement

    The leads running from the sensor to the P8 connector can become pinched, burned, or have their insulation worn through over time, causing the two leads to contact each other or the chassis. A visual inspection of the full harness length is necessary to identify this.

  5. 05

    Relay board fault misreading sensor signal

    Part replacement

    In rare cases, the relay board itself may be interpreting a normal sensor signal incorrectly due to a board-level component failure. This should only be considered after the sensor, harness, and connector have all been confirmed good.

See the test procedure for each cause

Frequently asked questions about F32

What does F32 mean on a Bosch range?
F32 on a Bosch range means the oven temperature sensor has been detected in a shorted condition. This means the sensor's resistance has dropped abnormally low, either from an internal sensor failure, the sensor or its leads contacting the chassis ground, or the leads shorting together. The oven will not operate until the fault is resolved.
Can I fix the F32 error myself?
A knowledgeable DIYer can start by checking the connector at P8 on the relay board to make sure it is fully seated, since a loose connection can trigger a false F32 code. If the connector is secure, testing resistance at the sensor leads with a multimeter is the next step. The sensor should read approximately 1100 ohms at room temperature across its leads and show an open circuit to chassis ground. If those readings are off, replacing the oven temperature sensor is a manageable repair for someone comfortable working on appliances, but the range must be fully disconnected from power before any work is done.
Is it safe to use my Bosch range when F32 is displayed?
No, you should not attempt to use the oven when F32 is active. The error indicates the temperature sensor is not functioning correctly, which means the oven cannot accurately monitor or control its internal temperature. Operating the oven in this condition could result in overheating. The oven will typically disable itself when this code is active, and that is the intended protective behavior.
How much does it cost to repair a Bosch range F32 error?
If the fix is simply reseating the connector at P8, there is no parts cost involved. If the oven temperature sensor needs replacement, the sensor part itself typically costs in the range of $20 to $80 depending on the model. Professional labor to diagnose and replace the sensor can add $100 to $250 or more to the total, depending on your location and the service provider.
Will resetting my Bosch range clear the F32 error?
Resetting the range by cutting power at the breaker for several minutes may temporarily clear the F32 code, but the code will return if the underlying fault is still present. A reset does not repair a shorted sensor, damaged wiring, or a faulty connection. If the code comes back after a reset, the sensor circuit needs to be properly diagnosed and repaired before the oven can be used reliably.

Related Bosch range codes

All Bosch range codes
View all 72 Bosch range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass