mypros+
Error code reference

Electrolux Dishwasher Error Code i44

Analog pressure sensor signal too low

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the i44 error code actually means

Your Electrolux dishwasher detected a problem with the sensor that monitors how much water is in the tub. The sensor is sending a signal that is too weak or missing entirely, so the dishwasher stopped the cycle to avoid running with the wrong water level. You will need to check the sensor and its connections before the dishwasher will run normally again.

Diagnostic procedure

The full i44 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check pressure sensor and its wiring; cycle stops and program is aborted.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock i44 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of i44

Ranked by how often they cause this code
  1. 1Faulty analog pressure sensor
  2. 2Damaged or disconnected wiring harness
  3. 3Blocked or kinked pressure hose
  4. 4Disconnected pressure hose
  5. 5Control board fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about i44

What does i44 mean on a Electrolux dishwasher?
The i44 code means the analog pressure sensor is producing a signal that is too low or has fallen outside the allowed range for more than 2.5 seconds. The pressure sensor is responsible for monitoring the water level inside the tub, and when its signal drops below the acceptable threshold, the dishwasher aborts the current cycle. The fault points to either the sensor itself, its wiring, or the air pressure hose connected to it.
Is it safe to keep using the dishwasher when the i44 code appears?
The dishwasher stops and aborts the program automatically when i44 is triggered, so it will not complete a wash cycle while the fault is active. Running the machine without a functioning water level sensor is not recommended, as the control board cannot verify the correct amount of water is present. Resolve the fault before resuming normal use.
How much does it cost to repair an i44 error on an Electrolux dishwasher?
If only the wiring connector needs to be reseated or the pressure hose reconnected, there may be no parts cost at all. A replacement pressure sensor typically costs in the range of $20 to $60 for the part alone. If a professional technician is needed, expect to pay between $100 and $250 in total depending on labor rates in your area and whether additional components such as the control board need to be replaced.
Can I fix the i44 error myself?
Some causes of the i44 error are accessible to a knowledgeable DIYer. Checking the wiring connector at the pressure sensor for looseness or corrosion, and inspecting the pressure hose for kinks or disconnection, require no special tools and can be done after removing the lower spray arm and filter assembly to access the sump area. If the sensor itself has failed, replacing it is a moderate-difficulty repair that involves disconnecting the hose and electrical connector and installing a compatible replacement part.
Will resetting the dishwasher clear the i44 error?
A reset may temporarily clear the displayed error code, but the i44 fault will return as soon as the dishwasher attempts to read the pressure sensor again and detects the same low signal. The underlying problem with the sensor, wiring, or pressure hose must be corrected for the fault to clear permanently.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass