mypros+
Model reference

Electrolux EDW1503

Dishwasher

6 documents78 error codes43 service modes

Available documentation

Service Manual

  • SERVICE MANUAL GESCHIRRSPÜLER mit EDW 150342 pg
    Covers this model
  • Service Manual Dishwasher Edw 150340 pg
    Covers this model
  • Service Manual Dishwashers37 pg
    Covers this model
  • Service Manual Dishwashers34 pg
    Covers this model
  • Service Manual Dishwashers39 pg
    Covers this model
  • Elektronikus vezérlőrendszerrel rendelkező mosogatógépek - SZERVIZ ÜZEMMÓD ÉS RIASZTÁSI KÓDOK SZERVIZ KÉZIKÖNYV35 pg
    Covers this model
MyPros+ Max

Diagnose your Electrolux EDW1503.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (78)

CodeMeaning
F0Pressure switch signal did not stabilize on FULL within the allowed fill time…i0Water tap closedi0 (10 blinks)Spray arm blockedi0 (11 blinks)Turbidity sensor faulti0 (12 blinks)Communication errori0 (13 blinks)Tacho faulti0 (14 blinks)Fill time errori0 (2 blinks)Drain pump faulti0 (3 blinks)Aqua-Control activatedi0 (5 blinks)Circulation pump triac short circuiti0 (7 blinks)NTC temperature sensor short circuit or open circuit.i0 (8 blinks)EEPROM communication errori0 (9 blinks)Checksum errori00Low or near-zero supply voltage detected; electronics pause all operations when…i10Water inlet failurei11Water fill problem during dynamic filli20Drain failurei30Aqua-Control water leak detectedi41Analog pressure sensori42Pressure sensor calibration invalidi43Analog pressure sensor signal too highi44Analog pressure sensor signal too lowi45Pressure sensor calibration invalidi46Pressure sensor calibration invalidi50Circulation pump triac short-circuiti51AC wash pump motor problemi52WP BLDC motori53WP BLDC (3-phase) motori54WP BLDC motor does not follow / rotor blockedi55DCLink low voltage
View all 78 error codes
i56DCLink overvoltagei57Platform-dependent: DIVA2i58WP motor connectori59WP BLDC motor ADC registered current errori5APlatform-dependent: DIVA2i5BWP/DP current problem suspectedi5CDP BLDC motori5DDP BLDC motori5EDP BLDC motor does not follow / rotor blockedi5FDP motor connectori60Heating failurei61Heater overtemperaturei62Heater relay damagedi63Heating system error 1 (newer platforms: PB100, PB101, PB150 R110+)i64Heater unit resettablei65Heater unit failed (newer platforms)i66Heating system error 2i67Heating system error 3i69Water temperature too highi6AHeater NTC sensor measurement value out of allowed range.i6BTemperature timeouti6CHeat exchanger efficiency lowi70NTC temperature sensor faulti80EEPROM communication errori81Automatic door opener warningi82Water recycling valve warningi90Checksum error in model programming (MCF) or CCFi91MCF checksum errori92CCF checksum errori93UIDATA checksum errori94UIDATA version mismatchi95UIDATA checksum type mismatchiA0Spray arm rotation not detectedib0Turbidity sensor signal faultyiB1Turbidity sensor communication lostiB2Turbidity sensor insufficient energy for calibrationiB3Turbidity sensor out-of-range calibration erroriB4Turbidity sensor too noisy during calibrationic0Communication error with user interface.iC1MACS bus communication failureiC2ADSI communication failureiC3Communication between circuit boards failedid0No tacho signal from circulation pumpiD1Tachometer critical warningiE0Flow diverter position error (spray arm level)iF0Filling time limit exceeded during water fill step.iF1High water levelSiOverheating

Service modes (43)

  • Activate/disactivate buzzer (user)1. Cancel any selected cycles. 2. Press S0 to switch on. 3. Press buttons S2-S3 simultaneously and…
  • Actuator Test (all models)["1
  • Additional rinse cycle on/off["1. Enter service function mode (S1+S3 held, then power on with S0, hold ~4 sec until LD1-LD3…
  • Alarm cancellation / LED test1
  • Alarm reading and component activation1
  • Buzzer activation/deactivation (user mode)1. Cancel any selected cycles. 2. Press S0 to switch on. 3. Press buttons S2-S3 simultaneously and…
  • Buzzer activation/disactivation (User)1
  • Cancel alarm codes / LED test1
  • Cancel alarm codes from memory / Test LEDs1
  • Customer function mode (Water hardness / Rinse aid / Signal tone)["1. Turn on the appliance with the On/Off button S0 (Vorstart mode
  • Customer service functions (water hardness, rinse-aid, signal sound)["Ensure no wash programme is selected.","Press keys S2 and S3 simultaneously.","Switch on…
  • Diagnostics mode1
  • Disable pulse washing (Service)1. Access diagnostics mode. 2. Press buttons S2 and S3 simultaneously. Display shows status
  • Disactivate rinse-aid function (user)1. Cancel any selected cycles. 2. Press S0 to switch on. 3. Press buttons S2-S3 simultaneously and…
  • Error memory readout and individual actuator control["1. Enter service function mode (S1+S3 held, then power on with S0, hold ~4 sec until LD1-LD3…
  • Extra cold rinse option (Service)1. Access diagnostics mode. 2. Press buttons S1 and S2 simultaneously. Display shows status
  • Factory test program (Fertigungsprüfprogramm)["1
  • Functional Test Cycle (all models)["EDW503
  • Functional testing cycle1
  • LED Test / Alarm Code Clear (all models)["EDW503
  • LED test with integrated error memory clearing["1
  • Manufacturing test routine["Ensure appliance is switched off.","Press keys S1 and S3 simultaneously.","While holding S1 and…
  • Pulse Wash on/off["1. Enter service function mode (S1+S3 held, then power on with S0, hold ~4 sec until LD1-LD3…
  • Read alarms and activate individual components1. Access diagnostics mode. 2. Press button S1 to start the function. LEDs LD2 and LD3 switch off…
  • Regeneration level setting (user mode)1. Cancel any selected cycles. 2. Press S0 to switch on. 3. Press buttons S2-S3 simultaneously and…
  • Regeneration level setting (User)1
  • Rinse-aid deactivation (user mode)1. Cancel any selected cycles. 2. Press S0 to switch on. 3. Press buttons S2-S3 simultaneously and…
  • Rinse-aid function disactivation (User)1
  • Service engineer disable pulse washing1. Access diagnostics mode. 2. Press buttons S2-S3 simultaneously. Display indicates status
  • Service engineer extra cold rinse option1. Access diagnostics mode. 2. Press buttons S1-S2 simultaneously. Display indicates status
  • Service function - Fault memory readout and single actuator selection["Ensure appliance is switched off.","Press keys S1 and S3 simultaneously.","While holding S1 and…
  • Service function - LED test with integrated deletion of fault memory["Ensure appliance is switched off.","Press keys S1 and S3 simultaneously.","While holding S1 and…
  • Service function mode (Error memory / Actuator test / LED test / Factory test / Pulse Wash / Additional rinse)["1. With the appliance OFF, press and hold buttons S1 and S3 simultaneously.","2. While holding S1…
  • Service Mode - EDW1103["1
  • Service Mode - EDW1503/EDW1753["1
  • Service Mode - EDW1953["1
  • Service Mode - EDW4013["1
  • Service Mode - EDW4033["1
  • Service Mode - EDW503["1
  • Service option - Disable pulse washing1
  • Service option - Extra cold rinse1
  • Service option - Force rinse-aid distribution1. Switch appliance on with S0. 2. Press buttons S2-S3 simultaneously until LEDs LD1-LD2-LD3 flash…
  • Set regeneration level (user)1. Cancel any selected cycles. 2. Press S0 to switch on. 3. Press buttons S2-S3 simultaneously and…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Electrolux dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax