Model reference
Electrolux EDW503
Dishwasher
2 documents63 error codes14 service modes
Available documentation
Service Manual
- Service Manual Dishwashers26 pg
- Elektronikus vezérlőrendszerrel rendelkező mosogatógépek - SZERVIZ ÜZEMMÓD ÉS RIASZTÁSI KÓDOK SZERVIZ KÉZIKÖNYV35 pg
MyPros+ Max
Diagnose your Electrolux EDW503.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (63)
CodeMeaning
i00Low or near-zero supply voltage detected; electronics pause all operations when…i10Water fill time-outi11Water fill problem during dynamic filli20Water drain time-outi30Intervention of the anti-flooding system causing the drain pump to switch on.i41Analog pressure sensori42Pressure sensor calibration invalidi43Analog pressure sensor signal too highi44Analog pressure sensor signal too lowi45Pressure sensor calibration invalidi46Pressure sensor calibration invalidi50Motor triac short-circuitedi51AC wash pump motor problemi52WP BLDC motori53WP BLDC (3-phase) motori54WP BLDC motor does not follow / rotor blockedi55DCLink low voltagei56DCLink overvoltagei57Platform-dependent: DIVA2i58WP motor connectori59WP BLDC motor ADC registered current errori5APlatform-dependent: DIVA2i5BWP/DP current problem suspectedi5CDP BLDC motori5DDP BLDC motori5EDP BLDC motor does not follow / rotor blockedi5FDP motor connectori60Heating time-outi61Heater overtemperaturei62Heater relay damagedView all 63 error codes
i63Heating system error 1 (newer platforms: PB100, PB101, PB150 R110+)i64Heater unit resettablei65Heater unit failed (newer platforms)i66Heating system error 2i67Heating system error 3i69Water temperature too highi6AHeater NTC sensor measurement value out of allowed range.i6BTemperature timeouti6CHeat exchanger efficiency lowi70NTC temperature sensor short-circuited or open circuit.i80Communication error between the microprocessor and the EEPROM; machine…i81Automatic door opener warningi82Water recycling valve warningi90Problems with software configuration; fault occurs when switching on, no…i91MCF checksum errori92CCF checksum errori93UIDATA checksum errori94UIDATA version mismatchi95UIDATA checksum type mismatchib0Problems with the turbidity meter (if featured)iB1Turbidity sensor communication lostiB2Turbidity sensor insufficient energy for calibrationiB3Turbidity sensor out-of-range calibration erroriB4Turbidity sensor too noisy during calibrationiC0User interface communication failureiC1MACS bus communication failureiC2ADSI communication failureiC3Communication between circuit boards failedid0Problems with the washing motoriD1Tachometer critical warningiE0Flow diverter position error (spray arm level)iF0Water replenishment time-out (3 times during the T.SiF1High water level
Service modes (14)
- Actuator Test (all models)["1
- Cancel Alarm Codes from Memory / LED Test["Enter Service Diagnostics Mode (press and hold S2, then press S0).","LED L2 flashes; LEDs L3 and…
- Functional Test Cycle (all models)["EDW503
- Functional Testing Cycle["Enter Service Diagnostics Mode (press and hold S2, then press S0).","LED L2 flashes; LEDs L3 and…
- LED Test / Alarm Code Clear (all models)["EDW503
- Service Diagnostics Mode (Alarm Reading and Component Test)["Press and hold down button S2.","While holding S2, press button S0 to switch the appliance…
- Service Mode - EDW1103["1
- Service Mode - EDW1503/EDW1753["1
- Service Mode - EDW1953["1
- Service Mode - EDW4013["1
- Service Mode - EDW4033["1
- Service Mode - EDW503["1
- User Mode - Buzzer Activation/Deactivation["Press button S0 to switch on the appliance.","Cancel any selected cycles by pressing button S2…
- User Mode - Regeneration Selection["Press button S0 to switch on the dishwasher.","Cancel any selected cycles by pressing button S2…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Electrolux dishwasher models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax