Model reference
Electrolux EDW4033
Dishwasher
1 document61 error codes9 service modes
Available documentation
Service Manual
- Elektronikus vezérlőrendszerrel rendelkező mosogatógépek - SZERVIZ ÜZEMMÓD ÉS RIASZTÁSI KÓDOK SZERVIZ KÉZIKÖNYV35 pg
MyPros+ Max
Diagnose your Electrolux EDW4033.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (61)
CodeMeaning
i00Low or near-zero supply voltage detected; electronics pause all operations when…i10Water tap closed or fill problem during static filli11Water fill problem during dynamic filli20Drain failurei30Water regulation faulti41Analog pressure sensori42Pressure sensor calibration invalidi43Analog pressure sensor signal too highi44Analog pressure sensor signal too lowi45Pressure sensor calibration invalidi46Pressure sensor calibration invalidi51AC wash pump motor problemi52WP BLDC motori53WP BLDC (3-phase) motori54WP BLDC motor does not follow / rotor blockedi55DCLink low voltagei56DCLink overvoltagei57Platform-dependent: DIVA2i58WP motor connectori59WP BLDC motor ADC registered current errori5APlatform-dependent: DIVA2i5BWP/DP current problem suspectedi5CDP BLDC motori5DDP BLDC motori5EDP BLDC motor does not follow / rotor blockedi5FDP motor connectori60Heating problem (older platforms: DIVA, DIVA2, PB150 R100, PB200, PB300)i61Heater overtemperaturei62Heater relay damagedi63Heating system error 1 (newer platforms: PB100, PB101, PB150 R110+)View all 61 error codes
i64Heater unit resettablei65Heater unit failed (newer platforms)i66Heating system error 2i67Heating system error 3i69Water temperature too highi6AHeater NTC sensor measurement value out of allowed range.i6BTemperature timeouti6CHeat exchanger efficiency lowi70NTC thermistor value out of rangei80Automatic door opener (ADO) failurei81Automatic door opener warningi82Water recycling valve warningi91MCF checksum errori92CCF checksum errori93UIDATA checksum errori94UIDATA version mismatchi95UIDATA checksum type mismatchiB0Turbidity sensor problemiB1Turbidity sensor communication lostiB2Turbidity sensor insufficient energy for calibrationiB3Turbidity sensor out-of-range calibration erroriB4Turbidity sensor too noisy during calibrationiC0User interface communication failureiC1MACS bus communication failureiC2ADSI communication failureiC3Communication between circuit boards failediD0Tachometer problemiD1Tachometer critical warningiE0Flow diverter position error (spray arm level)iF0Software fill limit reachediF1High water level
Service modes (9)
- Actuator Test (all models)["1
- Functional Test Cycle (all models)["EDW503
- LED Test / Alarm Code Clear (all models)["EDW503
- Service Mode - EDW1103["1
- Service Mode - EDW1503/EDW1753["1
- Service Mode - EDW1953["1
- Service Mode - EDW4013["1
- Service Mode - EDW4033["1
- Service Mode - EDW503["1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Electrolux dishwasher models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax