mypros+
Error code reference

Maytag Microwave Error Code F6 E7

Lost communications with Microwave Oven Appliance Manager.

Maytag codesMaytag microwave codes

Lost communications with Microwave Oven Appliance Manager.

First step from the service manual

Check microwave door light operation; check connection between UI board CN7-7 (orange) and microwave board P26-3 (orange), and UI board CN7-8 (yellow) and microwave board P26-2 (yellow).

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F6 E7.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F6 E7 means on a Maytag microwave

The F6 E7 error code on a Maytag microwave indicates a lost communications fault between the user interface (UI) board and the Microwave Oven Appliance Manager, which is the main microwave control board. These two boards continuously exchange data signals to coordinate functions like cooking modes, power levels, timer operations, and door interlocks. When that communication link is interrupted or fails to establish, the appliance manager flags the F6 E7 fault and typically halts operation to prevent uncontrolled behavior.

The communication link between these boards runs through specific wiring connections: UI board connector CN7 pins 7 and 8 connect to microwave board connector P26 pins 3 and 2, respectively. The CN7-7 to P26-3 wire is orange, and the CN7-8 to P26-2 wire is yellow. A break, loose pin, corrosion, or short in either of these wires will sever the data path and trigger this code. The diagnostic process begins with checking door light operation, which helps confirm whether the microwave board is receiving power and responding at a basic level before investigating the communication wiring.

If the wiring connections are intact and secure, the fault typically points to a failed UI board or a failed microwave control board. In some cases, moisture intrusion or arcing inside the cavity can damage board circuitry and cause communication failures. Because both boards must be functioning correctly for communication to succeed, isolating which board has failed usually requires substitution testing or board-level inspection by a qualified technician.

Source: manufacturer service documentation.

Common causes of F6 E7

  1. 01

    Loose or disconnected communication wire

    Wiring / connection

    The orange wire between UI board CN7-7 and microwave board P26-3, or the yellow wire between UI board CN7-8 and microwave board P26-2, may have come unseated from its connector. Check both ends of each wire for secure, fully seated connections.

  2. 02

    Corroded or damaged connector pins

    Wiring / connection

    Moisture or heat exposure inside the microwave cavity can corrode the connector pins at CN7 or P26, increasing resistance and breaking the communication signal. Inspect the pin contacts for discoloration, oxidation, or physical damage.

  3. 03

    Failed user interface (UI) board

    Part replacement

    If the wiring connections are intact, the UI board itself may have failed and can no longer send or receive communication signals. A failed UI board will typically require replacement to resolve the fault.

  4. 04

    Failed microwave main control board

    Part replacement

    The Microwave Oven Appliance Manager board may have failed due to component damage, arcing exposure, or age, making it unable to maintain communication with the UI board. Confirming basic power response through door light operation is a first step in ruling this out.

  5. 05

    Damaged wiring harness

    Part replacement

    The wiring harness running between the two boards may have a broken conductor, pinched section, or chafed insulation causing an intermittent or permanent open circuit. Carefully trace the orange and yellow wires along their full length for any visible damage.

See the test procedure for each cause

Frequently asked questions about F6 E7

What does F6 E7 mean on a Maytag microwave?
F6 E7 means the microwave has lost communication between the user interface board and the main microwave control board, called the Appliance Manager. The two boards communicate through a pair of wires connected at specific pins, and a fault in that communication path triggers this code. The microwave will typically stop operating until the fault is resolved.
Can I fix F6 E7 myself, or do I need a technician?
A knowledgeable DIYer can start by checking the door light operation and inspecting the orange and yellow communication wires at their connector pins for loose or corroded connections. If the wiring looks intact and secure, diagnosing a failed control board typically requires more advanced skills and component knowledge. Microwave capacitors store high-voltage charge even when unplugged, so internal access should only be performed by someone familiar with high-voltage appliance safety procedures.
Is it safe to use my Maytag microwave while F6 E7 is displayed?
No, you should not attempt to use the microwave while F6 E7 is active. The error indicates the control boards cannot communicate, which means the appliance cannot properly manage cooking functions or safety interlocks. Continued use in this condition could lead to unpredictable behavior.
Will resetting the microwave clear the F6 E7 error?
Unplugging the microwave for a few minutes may temporarily clear the code if the fault was caused by a transient communication glitch. However, if the underlying cause is a loose connector, damaged wire, or failed board, the error will return once power is restored. A reset alone is not a fix for a persistent F6 E7 fault.
How much does it cost to repair a Maytag microwave with an F6 E7 error?
Repair costs vary depending on the root cause. If the fix is simply reseating a loose connector, a service call fee may be the primary cost, typically ranging from $75 to $150. If a control board needs replacement, parts and labor combined can range from $150 to $350 or more, depending on the specific board required and local labor rates. In some cases, replacement of the unit may be more cost-effective than board-level repairs.

Related Maytag microwave codes

All Maytag microwave codes
View all 62 Maytag microwave codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass