mypros+
Error code reference

Sub-Zero Wine Storage Error Code 10 1 10

Zone 1 (upper wine) evaporator thermistor open circuit.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 10 1 10 error code actually means

This error means the temperature sensor in the upper wine storage section has stopped sending a readable signal to the unit's control board. Without that signal, the unit cannot properly monitor or control the temperature in the upper zone. A technician will need to inspect and likely replace the sensor or repair the wiring connected to it.

Diagnostic procedure

The full 10 1 10 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check ohms and verify temperature readings.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 10 1 10 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 10 1 10

Ranked by how often they cause this code
  1. 1Failed evaporator thermistor
  2. 2Disconnected or damaged wiring harness
  3. 3Corroded or loose connector terminals
  4. 4Ice buildup stressing sensor leads
  5. 5Faulty control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 10 1 10

What does 10 1 10 mean on a Sub-Zero wine_storage?
Error code 10 1 10 indicates an open circuit in the Zone 1 evaporator thermistor, which is the temperature sensor for the upper wine storage compartment. The control board is not receiving a valid resistance signal from that sensor. This prevents the unit from accurately monitoring and controlling the upper zone temperature. A technician will need to measure the thermistor resistance and inspect the associated wiring to locate the fault.
Is it safe to keep using my Sub-Zero wine storage with error code 10 1 10 active?
Continued use is not recommended without addressing the fault. Without a functioning Zone 1 thermistor, the control board cannot reliably regulate cooling in the upper compartment, which could result in temperature swings that may compromise stored wine. It is best to resolve the error promptly to protect both the wine and the unit.
Will resetting my Sub-Zero wine storage clear error code 10 1 10?
A power reset may temporarily clear the displayed error, but the code will return if the underlying open circuit condition in the Zone 1 thermistor or its wiring has not been corrected. Resetting the unit does not repair a failed sensor or damaged wiring. The fault must be diagnosed and the defective component repaired or replaced to permanently clear the code.
Can I fix error code 10 1 10 myself?
A knowledgeable DIYer can inspect the wiring harness and connector terminals for visible damage or disconnection, and can use a multimeter to check the thermistor's resistance. If the thermistor reads open or infinite resistance, replacing the sensor is a straightforward repair involving disconnecting the old sensor and connecting a correct replacement. However, accessing the evaporator area may require removing interior panels, and if the control board is suspected, professional diagnosis is recommended.
How much does it cost to repair error code 10 1 10 on a Sub-Zero wine storage?
If only the thermistor needs replacement, parts and labor typically range from around $100 to $300 depending on your location and service provider. If the wiring harness requires repair or replacement, costs can range from $150 to $400. A control board replacement, if needed, is significantly more expensive and can range from $400 to $800 or more including labor.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass