mypros+
Error code reference

Sub-Zero Wine Storage Error Code 10 3 10

Zone 3 (refrigerator) evaporator thermistor open circuit.

Sub-Zero codesSub-Zero wine storage codes

Zone 3 (refrigerator) evaporator thermistor open circuit.

First step from the service manual

Check ohms and verify temperature readings.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 10 3 10.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 10 3 10 means on a Sub-Zero wine storage

Error code 10 3 10 on a Sub-Zero wine storage unit indicates an open circuit condition in the Zone 3 evaporator thermistor. Zone 3 corresponds to the refrigerator section of the unit. The evaporator thermistor is a negative temperature coefficient (NTC) resistor that monitors the temperature of the evaporator coil in this zone. When the control board reads an open circuit, it means the thermistor circuit has infinite or unmeasurably high resistance, which prevents the board from receiving any valid temperature signal. This causes the unit to flag the fault and may affect cooling operation in the affected zone.

The primary diagnostic step is to measure the thermistor's resistance in ohms using a multimeter and cross-reference that reading against the expected resistance-temperature curve for the component. A properly functioning thermistor will show a predictable resistance value corresponding to the ambient evaporator temperature. An open circuit reading (OL or infinite ohms) confirms the thermistor itself has failed internally. If resistance reads within an expected range, the fault may lie in the wiring harness rather than the sensor itself, so inspecting connector pins, terminals, and wire routing for damage or corrosion is equally important.

Common causes include a failed thermistor that has developed an internal break, a disconnected or corroded wiring harness connector, or physical damage to the sensor lead wires. Because the thermistor is located near the evaporator coil, it can be exposed to moisture and freeze-thaw cycles over time, which accelerates connector corrosion and wire insulation degradation. Addressing this fault promptly is important because the control board cannot properly regulate Zone 3 cooling without a valid evaporator temperature signal.

Source: manufacturer service documentation.

Common causes of 10 3 10

  1. 01

    Failed evaporator thermistor

    Part replacement

    The thermistor itself has developed an internal open circuit, producing infinite resistance when measured with a multimeter. This is the most common cause and requires replacing the sensor.

  2. 02

    Disconnected wiring harness connector

    Wiring / connection

    The connector joining the thermistor leads to the main wiring harness may have worked loose over time. Inspect the connector at the thermistor and at the control board for proper seating.

  3. 03

    Corroded or oxidized connector terminals

    Wiring / connection

    Moisture near the evaporator coil can cause terminal corrosion that increases resistance to the point of an open circuit. Check terminals for visible oxidation or greenish discoloration and clean or replace as needed.

  4. 04

    Damaged thermistor lead wires

    Part replacement

    The insulated wires running from the thermistor to the harness can crack or fray due to repeated freeze-thaw cycling or physical contact with sharp edges inside the unit. Inspect the full wire run for damage.

  5. 05

    Control board input fault

    Part replacement

    In rare cases, the thermistor circuit input on the control board itself may be damaged, causing it to misread a functioning thermistor as an open circuit. This should only be considered after confirming the thermistor and wiring check out correctly.

See the test procedure for each cause

Frequently asked questions about 10 3 10

What does 10 3 10 mean on a Sub-Zero wine_storage?
Error code 10 3 10 indicates an open circuit in the Zone 3 evaporator thermistor, which is the temperature sensor mounted near the evaporator coil in the refrigerator section of the wine storage unit. An open circuit means the control board is receiving no valid resistance signal from that sensor. The unit cannot properly regulate Zone 3 cooling until this fault is resolved.
How do I fix error code 10 3 10 on my Sub-Zero wine storage?
Start by using a multimeter to measure the resistance across the Zone 3 evaporator thermistor. An open circuit reading confirms the thermistor has failed and needs replacement. If the thermistor reads within a normal range, inspect the wiring harness connectors and lead wires for corrosion, looseness, or physical damage. Addressing the faulty component or connection should clear the fault.
Is it safe to continue using my Sub-Zero wine storage when error 10 3 10 is displayed?
The unit may continue running, but it cannot reliably maintain proper temperature in Zone 3 without a functioning evaporator thermistor. This puts the contents of that zone at risk of improper storage temperatures. It is best to address the fault promptly and avoid storing temperature-sensitive wines in the affected zone until the repair is complete.
Will resetting my Sub-Zero wine storage clear error code 10 3 10?
A reset may temporarily clear the displayed error code, but the fault will return if the underlying problem with the thermistor or its wiring has not been corrected. The control board will detect the open circuit again during normal operation and re-trigger the code. A proper repair of the sensor or wiring is required for a lasting resolution.
How much does it cost to repair error code 10 3 10 on a Sub-Zero wine storage unit?
Repair costs vary depending on whether the issue is a failed thermistor, damaged wiring, or a control board problem. Thermistor replacement parts are generally in the range of $20 to $80, while professional labor to diagnose and complete the repair typically adds $100 to $250 or more depending on the technician and region. If the control board is involved, total costs can be significantly higher.

Related Sub-Zero wine storage codes

All Sub-Zero wine storage codes
View all 72 Sub-Zero wine storage codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass