Error code reference
Whirlpool Oven Error Code E2 F2
Stuck key detected on keypad.
Stuck key detected on keypad.
First step from the service manual
1
Verify failure in diagnostics mode Faults screen, then unplug range and check keypad connection; replace keypad if necessary.
The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.
MyPros+ Max
Get the full diagnostic procedure for E2 F2.
- ✓Step-by-step tests with expected resistance, voltage, and continuity values
- ✓Wiring diagram references and connector pinouts from the OEM service manual
- ✓Verified part numbers when replacement is required
Get the full procedure→
$29/month · Cancel anytime · Or $9.95 3-day pass
M+
M+ Max·Whirlpool Oven
E2 F2 on my Whirlpool Oven
M+
Stuck key detected on keypad
From Tech Sheet W17490239, p.51:
1.Verify failure in diagnostics mode Faults screen, then unplug range and check keypad connection; replace keypad if necessary.
2.Measure control board supply voltage at the test points. Expected: 12 VDC and 5 VDC; a drop below 4.75 VDC on the logic rail points to a failed onboard regulator.
3.Inspect all connectors on the main control for corrosion, thermal stress, or backed-out pins. Reseat each connector with the power disconnected.
Part WPW10804018
Electronic control board
Related Whirlpool oven codes
All Whirlpool oven codes →- 11Oven sensor opened (upper oven).
- 12Oven sensor shorted (upper oven).
- 1CShorted key detected on keypad.
- 1dDoor and switches do not agree
- 21Oven sensor opened (lower oven).
- 22Oven sensor shorted (lower oven).
- 2CKeytail unplugged
- 31EEPROM communications error (internal control error).
View all 187 Whirlpool oven codes
- 32EEPROM communications error (internal control error).
- 3dDoor and switches do not agree
- 4dDoor latch not operating properly.
- 51BAKE/BROIL range over temperature condition.
- 52CLEAN range over temperature condition.
- 6CEEPROM communications error (internal control error).
- 7CEEPROM communications error (internal control error).
- 8CEEPROM communications error (internal control error).
- 9dLatch error during CLEAN cycle.
- C-81Induction cooktop over temperature (Type 2 failure).
- C-82Induction cooktop over temperature (Type 2 failure).
- C-83Induction cooktop temperature sensor stuck (Type 2 failure).
- E0Key held down too long or key is shorted (under F2).
- E0 E5 E7 E9Internal board failure (F1).
- E0 F0No failure (GOOD)
- E0 F1EEPROM communication error (internal control failure).
- E0 F2Keypad disconnected from control.
- E0 F3Main oven temperature sensor open or shorted (upper cavity).
- E0 F5Door and latch switches do not agree during Clean mode.
- E0 F6Lost communications between user interface and appliance…
- E0 F9Range is mis-wired (incorrect power supply wiring).
- E1Oven temperature sensor open or shorted (upper or lower…
- E1 E5Oven user interface failure.
- E1 F1Check oven appliance manager
- E1 F2Stuck or shorted key on keypad.
- E1 F3Main oven temperature sensor open or shorted (lower cavity).
- E1 F5Door latch not operating during Clean mode.
- E1 F6Over temperature condition during cook mode (runaway…
- E2Oven temperature too high or runaway oven condition.
- E2 F1Lower RTD uncalibrated (internal control failure).
- E2 F3Warming drawer sensor shorted or open (oven not equipped…
- E2 F6Over temperature condition during clean mode (runaway…
- E3Wiring harness cavity size select jumpers indicate a cavity…
- E3 F3Meat probe shorted.
- E3 F6Mini oven/warm drawer over temperature (oven not equipped…
- E4Door latch unlock failure
- E4 F6User interface / appliance manager mismatch.
- E5Control board failure
- E5 F1Sensor usage out of range (internal control failure).
- E5 F6No cavity size command programmed in control.
- E6CANCEL key drive line open (under F2).
- E7Self clean latch will not unlock.
- E7 F1PCB thermistor/sensor open or shorted.
- E9 F1WIDE Queue full (internal communication buffer overflow).
- EEPROMEEPROM communication error.
- F-12Induction cooktop coil under current (Type 1 failure…
- F-21Induction cooktop supply power frequency error (Type 2…
- F-25Stuck fan on Induction Power System (IPS)
- F-36Stuck fan on Induction Power System (IPS) (right or left…
- F-37Stuck fan on Induction Power System (IPS) (right or left…
- F-40Induction Power System (IPS) failure (Type 1 or Type 2).
- F-42Induction cooktop power supply issue (Type 2 failure).
- F-43Induction cooktop under voltage (Type 2 failure).
- F-47Power supply from Induction Power Control (IPC) to User…
- F-56Wrong or invalid configuration (Type 3 failure, disables…
- F-58Wrong or invalid configuration on the Induction Power…
- F-60UI does not work (Type 3 failure, disables entire cooktop).
- F0Default F code
- F0-E0Default F code
- F0-E3Wiring harness cavity size does not match previously stored…
- F01Temperature probe failure
- F02Welded (stuck closed) element relays detected on the…
- F03A.M
- F04WISP protocol doesn't work (communication error between…
- F05Door or latch problems (door latch assembly, motor, or…
- F06Door closure failure
- F07Gemini/Capricorn failure (short circuit)
- F08UI EEPROM failure (TAD models).
- F09Communication failure between G2SMART and Antares (TAD…
- F1Control failure series: potential runaway oven condition…
- F1 E3Configuration jumper change; freestand, electric switches…
- F1 E8Improper keypad feedback (power board supply lift).
- F1-E4Electronic control malfunction (E4 variant).
- F1-E6Electronic control malfunction (all E codes under F1…
- F1-E7 (cooktop)PCB thermistor/sensor open or shorted on the cooktop…
- F1-E9 (cooktop)WIDE queue full on the cooktop control.
- F10Primary grill heating element failure (Pyro models only).
- F11Communication failure between G2SMART and TEX (TAD models).
- F1E0User Interface Board EEPROM Communication Error
- F1E0 (cooktop)EEPROM communication error on cooktop (EGO) control.
- F1E1Control Relay Board EEPROM Communication Error
- F1E2Lower RTD Uncalibrated
- F1E5Sensor Usage Out of Range
- F1E7PCB Thermistor Open or Shorted
- F1E9WIDE Queue Full
- F1EAMain ACU over temperature condition.
- F1EBControl panel not working/Control panel not accepting…
- F2Default F code
- F2 E3Key held down too long or keyboard short or spill on switch…
- F2 E5Cancel key drive line open.
- F2-E1 (cooktop)Stuck key detected on the cooktop control keypad.
- F2E0Keypad Disconnected
- F2E1Stuck Key
- F2E2Cancel or Off Key Error/Warming Zone Off Keypad Error
- F2E4Temperature Too Low (cooking times too long, not getting…
- F2E6Keypad error (microwave generation related).
- F3Oven sensor open circuit, oven sensor short circuit…
- F3 EOOven sensor open or shorted (humidity sensor 1600).
- F3-E4Bottom oven temperature sensor open (bottom oven sensor…
- F3-E5Bottom oven temperature sensor shorted (bottom oven sensor…
- F3-E7Warming drawer temperature sensor shorted.
- F3E0Main Sensor Open or Shorted (Upper)
- F3E1Main Sensor Open or Shorted (Lower)
- F3E2Warming drawer sensor short-circuited (not applicable to…
- F3E3Main Oven Meat Probe Short-Circuit
- F3E6Powered Accessory (PA) over temperature.
- F3E8Main oven Powered Accessory (PA) mismatch.
- F3E9Left Oven Meat Probe Short-Circuit
- F4Temperature sensor opened or temperature sensor shorted…
- F4 E2Over temperature during cook mode (temperature runaway).
- F4 E3Over temperature during clean mode (temperature runaway).
- F4 E7Over temperature cavity 2 (temperature runaway error).
- F4-E0Door is open but latch is locked (door switch indicates…
- F4E1Microwave Oven Magnetron Thermistor Open or Shorted
- F4E4Microwave Oven Humidity Sensor Open or Shorted
- F4E8Inverter over temperature.
- F4E9Inverter and magnetron over temperature.
- F5Door and latch switch mismatch during clean mode, or door…
- F5 E6Lower door switch reads constant high.
- F5 E7Door unlocked but will not unlatch after clean cycle.
- F5 EODoor and latch switch do not agree.
- F5-E5Self clean temperature (288°C [550°F]) not reached within…
- F5E0Door and Latch Switches Do Not Agree
- F5E1Latch Not Operating
- F5E2CLEAN range over temperature, or door and door position…
- F5E3Left Oven Door Latch Switch
- F5E3 (Inputs)Door and latch switch do not agree (lower oven).
- F5E4Left Oven Door Latch Motor
- F6Switch pulse return line not connected
- F6 E0 (cooktop)Right cooktop communication error.
- F6 E1 (over temp)Over temperature during cooking.
- F6 E4 (cooktop)Left cooktop communication error.
- F6 E7Lost communication with MWO appliance manager.
- F6 E8Lost communications with Microwave Oven Appliance Manager.
- F6 EAUser interface over temperature.
- F6 EBDouble lower oven
- F6E0User Interface Connection
- F6E1Over Temp Cook
- F6E2Over Temp Clean
- F6E3Left Oven Over Temperature Limit
- F6E4Control Status
- F6E5Mini oven/warm drawer over temperature (oven not equipped…
- F6E5 (cooktop)Oven control communication error (from cooktop control…
- F6E6Main Oven Control Connection
- F6E9Left Oven Control Connection
- F7Common wire (+5VDC) to latch switch and door switch is…
- F7-E0Boiler
- F7-E3Incorrect filter reset.
- F7-E4Conductivity sensor not connected.
- F7E1Boiler Over Temperature Limit (steam models)
- F7E2Boiler Temperature Out of Range (for steam models)
- F7E5Main cooling fan error
- F7E6Microwave Inverter and Magnetron fault.
- F8Defective electronic oven control
- F8-E4Oven over temperature while door close and latch unlock.
- F8-E6Left fan at high speed
- F8E0Cooling Fan Speed Too Low
- F8E1Left Oven Cooling Fan Speed Low
- F8E2Cooling Fan Speed Too High
- F8E3Left Oven Cooling Fan Speed High
- F9Door motor mechanism failure (F90 to F94)
- F9E0Error code listed in error code table (specific description…
- F9E4User interface/Appliance manager state status mismatch.
- FBE1Main Door Latch motor has failed to lock/unlock.
- FCE1Secondary Door and Latch Switches Do Not Agree (Lower Oven).
- FCE2Model/Serial Numbers Do Not Match.
- FCE3Common Failure Between Main ACU and HMI.
- FEE6Main Cavity Bake Element open circuit.
- FEE7Main Cavity Broil Element open circuit.
- FEE8Main Cavity Convect 1 Element open circuit.
- FEE9Main Cavity Convect 2 Element open circuit.
- FEEAMain Cavity Convect 2 Element open circuit.
- FEEBSecondary Cavity Broil Element open circuit.
- FEECConvection element open circuit.
- FEEDSecondary Cavity Convect 2 Element open circuit.
- Microwave Oven Inverter ErrorMicrowave oven inverter error
- No DisplayControl is blank
- PFPower failure indication (not a failure mode).
- SABOven is in Sabbath Mode.
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started →$29/month · Cancel anytime · Or $9.95 3-day pass