Model reference

Whirlpool GGE388LXB02

Name: Whirlpool GGE388LXB02
Brand: Whirlpool

Range

3 documents30 error codes16 service modes

Available documentation

Tech Sheet

Tech Sheet - W10311742 - Rev A16 pg
Covers this model
Whirlpool Oven GGE388LXS01 Tech Sheet16 pg
Covers this model

Service Manual

Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool GGE388LXB02.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

E0 F1 on my Whirlpool GGE388LXB02

M+

EEPROM communication error (internal

From Tech Sheet W13021501, p.33:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (30)

CodeMeaning

E0 F1EEPROM communication error (internal control failure).E0 F2Keypad disconnected from control.E0 F3Upper oven main temperature sensor open or shorted.E0 F5Door and latch switches do not agree during Clean mode.E0 F6Lost communications between control boards.E0 F9Range is mis-wired (incorrect power supply wiring).E1 F1Upper RTD uncalibrated (internal control failure).E1 F2Stuck key detected on keypad.E1 F3Lower oven main temperature sensor open or shorted.E1 F5Door latch not operating during Clean mode.E1 F6Over temperature condition during cook mode (runaway temperature).E2 F1Lower RTD uncalibrated (internal control failure).E2 F2Stuck key detected on keypad.E2 F6Over temperature condition during clean mode (runaway temperature).E3 F6Over temperature condition in warming drawer (runaway temperature).E5 F1Sensor usage out of range (internal control failure).E7 F1PCB thermistor/sensor open or shorted.E9 F1WIDE Queue full (internal communication buffer overflow).F1Control failure or UL A/D error(s) detected in the control board.F1 E*Control board failure (all F1 sub-codes indicate control fault).F2Shorted/stuck key detected on the control keypad.F3Oven sensor opened or oven sensor shorted.F3 E0Oven temperature sensor fault (open or shorted)F3 E1Lower oven temperature sensor fault (MRC II double oven models).F3 E2Warming drawer temperature sensor fault.F5 E0Door position switch fault F5 E1Door latch switch/system fault F5 E2Door switch fault.F6 E*Control communication failure.F9House miswired

Service modes (16)

Control ResetFrom Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads depending on…
Diagnostics ModePress CANCEL > CANCEL > START within 5 seconds
Display TestFrom Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads depending on…
Faults DisplayFrom Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads depending on…
LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
Semi Automatic TestEnter Diagnostics Mode first (CANCEL > CANCEL > START within 5 seconds)
Temperature CalibrationPress SETTINGS/OPTIONS until 'Temp Calib' is highlighted, then follow on-screen instructions
Test ModeEnter Diagnostics Mode first (CANCEL > CANCEL > START within 5 seconds)
Test Mode (Manual Relay Activation)From Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads depending on…
Usage ModeFrom Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads depending on…
Version DisplayFrom Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads depending on…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass