mypros+
Model reference

Amana YY-100-PA

Furnace

6 documents75 error codes20 service modes

Available documentation

Tech Sheet

  • tech sheet w11359197 reva2 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 397920812 pg
    Covers this model
  • Instruction Sheet - 854179812 pg
    Covers this model
  • Instruction Sheet - 397921012 pg
    Covers this model

Installation Guide

  • Installation Instructions24 pg
    Covers this model
  • Installation Instructions58 pg
    Covers this model
MyPros+ Max

Diagnose your Amana YY-100-PA.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (75)

CodeMeaning
F0-E0Default F codeF0E1Load detected during the washer cleaning cycleF1-E0Electronic control malfunction (E0 variant).F1-E1Electronic control malfunction (E1 variant).F1-E2Electronic control malfunction (E2 variant).F1-E3Electronic control malfunction (E3 variant).F1-E4Electronic control malfunction (E4 variant).F1-E5Electronic control malfunction (E5 variant).F1-E6Internal error.F1-E7Internal error.F1-E8Internal error.F1-E9Internal error.F1E0EEPROM communications error.F1E1EEPROM checksum failure.F1E2UL A/D error(s).F1E4Microwave ACU PCBA failure.F2-E0Keypad keytail not connected.F2-E1Keypad keytail not connected.F2-E3Key held down too long, or key is shorted.F2E0Shorted keypad.F2E1Stuck key failure on the touch panel.F2E3Unsupported CycleF3-E0Temperature sensor (lower) opened.F3-E1Temperature sensor (lower) shorted.F3-E2Temperature sensor (microwave) opened.F3-E3Temperature sensor (microwave) shorted.F3-E4Bottom oven sensor open (bottom oven sensor open).F3-E5Lower sensor short or bottom sensor short (bottom oven sensor shorted).F3-E6Warm drawer sensor open (warming drawer sensor open).F3-E7Warm drawer sensor shorted (warming drawer sensor shorted).
View all 75 error codes
F3E0Oven sensor opened.F3E1Oven sensor shorted.F3E2Bake range over-temperature.F3E3Clean range over-temperature.F4-E0Meat probe shorted.F4-E2Over temperature during cook mode.F4-E3Over temperature during clean mode.F4-E7Over temperature cavity 2 (temperature runaway error).F4E1Cavity temperature sensor failure.F4E4Humidity sensor error.F4E9AccuPop error.F5-E0Lower cavity over temperature while cleaning.F5-E1No operating latch or latch not operating.F5-E2Door switch fault.F5-E4Latch switch fault.F5-E7Unlock door errorF5E0Door and latch switches do not agree.F5E1Solenoid not operating or latch switch failure.F5E2Door Lock ErrorF5E3Door Unlock ErrorF6-E0Lower cavity over temperature during cooking.F6-E1Microwave cavity over temperature during cooking.F6-E4Lost communication between power board and display board.F6-E5Cancel key error.F6E1Communication Error between CCU and MCUF6E2Communication Error UI to CCUF6E3Communication Error CCU to UIF7E1Drive Motor Tachometer Error / Washer OverloadF7E2MCU Fault or Motor OverheatF8-E0Self-clean latch will not lock.F8-E1Self-clean latch will not unlock.F8-E2Oven over temperature while door open and latch lock.F8-E3Oven over temperature while door open and latch unlock.F8-E4Oven over temperature while door close and latch unlock.F8E0Steam Inlet Valve ErrorF8E1No water detected entering washer or pressure switch trip not detectedF8E2Dispenser System ErrorF8E3Overflow ConditionF8E4Flow Meter FaultF8E5Exhaust air template detector (HF NTC thermistor) failure.F9E1Long DrainIntInterruptedrLRemove LoadSABOven is in Sabbath Mode.SudSuds detected

Service modes (20)

  • Advancing Through Saved Fault/Error Codes1
  • Bake temperature offset adjustment1
  • Clear Fault Codes1
  • Default F code display (no-fault check)Press and hold '0' key for 5 seconds
  • Default F code display (no-fault verification)Press and hold '0' key for 5 seconds
  • Diagnostic mode (recall last failure code)["Press the Cancel key to place the range in an idle state.","Press the Cancel and Start keys in…
  • Diagnostic/Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL keypad to Standby mode (displays…
  • Diagnostics mode (Failure code verification)["Press CANCEL","Press CANCEL","Press START"]
  • Fahrenheit to Celsius conversionPress the BROIL pad for 5 seconds
  • Fault Code Display / Advance1
  • Last Error Code RecallPress and hold the CANCEL/OFF key for 5 seconds until the last error code is displayed.
  • Oven temperature calibrationPress and hold the BAKE keypad for 5 seconds. 'CAL' is shown in the display. Press the TEMP/TIME Up…
  • Quick Diagnostics1
  • Sabbath Mode checkIf 'SAB' appears in digital display, oven is in Sabbath Mode.
  • Service Diagnostic Mode1. Ensure washer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Software Version Display1
  • Temperature Calibration AdjustmentPress and hold the BAKE pad for 5 seconds. Current offset (if any) is shown in the 3-digit display…
  • Temperature unit conversion (Fahrenheit to Celsius)Press the BROIL pad for 5 seconds
  • Touch Panel and ACU PCBA Test (Test Mode)["Plug in microwave oven or reconnect power and press the Cancel keypad to standby (':')","Close…
  • User Interface Test1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass